User Manual
Table Of Contents
- Contents
- Important Information
- Notices
- Description
- Installation
- Configuration
- Overview
- Accessing the Main Menu
- Configuring with the Main Menu
- Unit Identification
- Hardware/Software Revision
- System Software ROM Images
- System Current Status
- Network Configuration
- IP Filter Configuration
- VLAN Configuration
- Viewing VLAN Configuration
- Port Configuration
- Press Esc to exit the menu
- Setting the Default VLAN ID
- Setting the Port Link Type
- Setting the Port Priority
- Setting the Port Acceptable Frame Type
- Enabling Port Ingress Filtering
- Enabling Port Egress Filtering
- VLAN Registration Configuration
- Creating/Modifying a VLAN Registration Entry
- Deleting a VLAN Registration Entry
- Displaying the VLAN Registration Table
- Below is a sample table:
- MAC Address Filter Configuration
- Creating/Modifying a MAC Address Filter Entry
- Removing a MAC Address Filter Entry
- Displaying the MAC Address Filter Table
- Below is a sample table:
- Traffic Class Configuration
- Á To view the Traffic Class Configuration menu
- Assigning Packet Priority to Traffic Classes
- Spanning Tree Configuration
- Á To view the Spanning Tree Configuration menu
- Enabling Spanning Tree
- Setting the Bridge Priority
- Setting Port Priority
- Setting Port Path Cost
- RF Station Configuration
- Viewing Current RF Station Configuration
- Setting the Operating Mode
- Setting Test Mode Timer Minutes
- Performing Link Monitor Test (Normal Mode)
- Performing Transmit and Receive Tests
- Setting the RF Transmit Status
- Setting the Link Monitor Period
- Setting Maximum Remote Distance (Base Station Only)
- Setting Link Monitor Remote Station Rank
- Adjusting Throttling (Remote Station Only)
- Setting Tx Power Automatically (Remote Station Only)
- Adjusting User Output Power Ceiling (Remote Station Only)
- Setting Signal Margin (Remote Station Only)
- Viewing Current Output Power Level Adjust
- Radio Module Configuration
- Viewing the Radio Module Configuration
- Setting Config Test Minutes
- Setting the Station Type
- Setting the Station Rank
- Setting the Center Frequency
- Setting Security Passwords
- Setting the Scrambling Code
- Setting the Acquisition Code
- Adjusting the Tx Power Level
- Setting a Base to Repeater Mode (Base Station Only)
- Setting System Symmetry Type (Base Station Only)
- Setting Dynamic Polling Level (Base Station Only)
- Setting Remote Unit RF Group
- Rebooting and Saving RF Module Configurations
- RF/Ethernet Statistics
- System Security
- System Commands
- Link Monitor Display
- Logout
- Command Line Interface
- Troubleshooting
- Appendix A: Planning Your Wireless Link
- Appendix B: Using HyperTerminal
- Appendix C: Configuring a Simple Data Network
- Appendix D: SNMP
- Appendix E: Configuration Via the Web
- Appendix F: Upgrading Software
- Appendix G: Network Plan Template
- Index
Radio Module Configuration
APR 2002 Rev 03
97
➧
To set the center frequency
1. From the Main Menu, select Radio Module Configuration and press
Enter. The Radio Module
Configuration menu is displayed.
2. Select Center Frequency and press
Enter. The data field highlights.
3. Type the value of the RF center frequency. The value can range from 5.7410 GHz to 5.8338 GHz in steps
of 400 kHz. (Numbers are automatically rounded down to the nearest step.) All units in a system must
have the same center frequency.
4. Press
Enter. The new setting is displayed in the “New column.
5. Select Reboot New RF Configuration and press
Enter. The unit reboots and the AWE 120-58
Login menu is displayed. The unit now runs using the “Current” center frequency for the amount of
time specified by Config Test Minutes.
6. To save the current setting(s) to flash memory, log in, go to the Main Menu, and select Radio Module
Configuration, Save Current Config to Flash. See Rebooting and Saving RF Module
Configurations , page 109.
7. Press
Esc to exit to the Main Menu.
H - Help Radio Module Configuration
New Current Flash
Station Type Remote Unit Remote Unit Remote Unit
Station Rank (1-1000) 1 1 1
Center Frequency (57410-58338) -> 5.7874 GHz 5.7874 GHz 5.7874 GHz
Security Password 1 (Hex) 1 1 1
Security Password 2 (Hex) 10 10 10
Security Password 3 (Hex) 100 100 100
Security Password 4 (Hex) 1000 1000 1000
Security Password 5 (Hex) 10000 10000 10000
Scrambling Code (Hex) 0 0 0
Acquisition Code (0-15) 1 1 1
Config Test Minutes (1-120) 30 30 30
Tx Power Level Adjust 0 dB 0 dB 0 dB
Base Station Only Parameters
Repeater Mode off off off
System Symmetry Type Asymmetric Asymmetric Asymmetric
Dynamic Polling Level (1-100) 1 1 1
Remote Station Only Parameters
Remote Unit RF Group (0-63) 0 0 0
Reboot New RF configuration Press Enter to Execute
Save Current Config to Flash Press Enter to Execute