DOME PREMIUM GENUINE FILM Installation User Guide User Guide • Please check all manual and attachment videos before using the product. • Products damaged or damaged by user negligence cannot be exchanged or refunded.
Dome Premium Genuine Film Installation User Guide Please make sure to check manual and installation video before using the product. Products damaged or damaged by user usage, cannot be exchanged or refunded. After checking the Quick guide, check the User guide. Please check the model and components before using the product. • Match your device model with the product in advance.
Dome Premium Genuine Film Installation User Guide Components Reference • There may be differences in components depending on the model. • To improve the product, component's appearance or specifications etc. can be change without prior notice. *There are differences in components depending on the model, so please check the components of the product purchased before attaching it.
Dome Premium Genuine Film Installation User Guide Installation STEP1 Remove the protection film attached to your device using the Remover. ※Correct film removal direction※ STEP2 Connect the Align block to top part of the JIG.
Dome Premium Genuine Film Installation User Guide Installation STEP3 Insert the device into the JIG in correct direction. Top – Speaker Bottom – Connector STEP4 Clean the display with alcohol wipe and cleaning cloth. Then, remove any dust with dust removal sticker. Close the device to the stopper. 5 Close the device to the stopper.
Dome Premium Genuine Film Installation User Guide Installation STEP5 Hold the top part of the film as shown, and bend the [1 sticker] as shown in [Figure 1]. Like [Figure 2] Make sure that the protective film and pet film are properly separated and slowly remove the protective film. If it is as shown in [Figure 3], attach the protective film as if it is in the first state and remove it carefully so that only the protective film can be removed. • Please do not touch adhesion surface.
Dome Premium Genuine Film Installation User Guide Installation STEP7 Hold the top end of the film and slowly and forcefully push up with the squeegee from the bottom of the jig to the top while maintaining squeegee in a lean angle. Push the squeegee all the way to the end. • Bubble might be appeared if you push the squeegee too fast.
Dome Premium Genuine Film Installation User Guide Installation STEP8 Remove the guide film from Jig's hole while pressing the ①-top/②-bottom of the film with a squeegee. ③Push the film entirely to the short side of the squeeze. ① ② ③ Push the squeegee in a horizontal direction.
Dome Premium Genuine Film Installation User Guide Installation STEP9 Bend the guide film attached to the film and remove it from the top. Finish by pressing the film edge with the short part of the squeegee. Remove the device from the JIG. • Micro bubbles will disappear within a week.
Dome Premium Genuine Film Installation User Guide Installation-Outer display (There are differences in components depending on the model) STEP1 Use the alcohol wipe and the cleaning cloth to wipe down the device. Remove any dust on your device with the dust remover sticker. STEP2 Remove liner film(back). Align the film starting with the top edges of the device.
Dome Premium Genuine Film Installation User Guide Installation-Outer display (There are differences in components depending on the model) STEP3 Tilt the protective film (1)180° and push with a squeegee to attach it. Tilt the protective film (2)180° and push with a squeegee to attach it. STEP4 Remove any bubbles with a squeeze. With a dust removal sticker remove the front protective film. * Please do not press the bubbles or lines after the installation, it will be naturally disappeared.
Dome Premium Genuine Film Installation User Guide Installation-Hinge (There are differences in components depending on the model) STEP1 Use the alcohol wipe and the cleaning cloth to wipe down the device. Remove liner film[1].Place it on the device and attach it in position. Tilt the protective film (2)180° and push with a squeegee to attach it. Tilt the protective film (3)180° and push with a squeegee to attach it. With a dust removal sticker remove the front protective film.
Dome Premium Genuine Film Installation User Guide Please check the installation Guide. Precautions after installation • Bubbles or lifting may occur by physical impacts such as drop impact, incompatible phone cases use, excessive strength while cleaning with alcohol wipes or etc. • No refund or exchange for any type of user damages. ※Global A/S※ CONTACT US feedback@whitestonedome.com HOMEPAGE www.whitestonedome.com > WARRANTY REQUEST We always provide friendly and fast service to your questions.
The unique Component Manufacturer, Whitestone (www.whitestonedome.com) for Mobile Device. Copyright ⓒ Whitestone Ltd. All rights reserved.
