&$) INSTALLATION AND SERVICE INSTRUCTIONS Keep this booklet for future reference. The dryer must be fitted by a competent person. In the U.K. Registered Installers undertake to work to safe and satisfactory standards. The dryer must be installed in accordance with the Gas Safety (Installation and Use) Regulations 2009. Guidance may be obtained from the relevant parts of B.S. 7624: B.S. 5440 parts 1 and 2, B.S. 6891: current editions, I.E.E. Wiring Regulations, and relevant Building Regulations.
Contents Technical Data Installation Service instructions Wiring diagram Exploded views Parts list WARNING THIS APPLIANCE SHALL BE INSTALLED IN ACCORDANCE WITH THE LOCAL REGULATIONS IN FORCE AND ONLY IN A WELL VENTILATED SPACE.READ THE INSTRUCTIONS BEFORE USING OR INSTALLING THIS APPLIANCE. THIS APPLIANCE CONFORMS TO THE FOLLOWING EEC DIRECTIVES. LOW VOLTAGE DIRECTIVE LVD 2006/95/EC:EN60335-1, EN60335-2.11.
TECHNICAL DATA CONTROL GENERAL Type:Pactrol full sequence flame control, P16AGTD(CE) 414601. Ignition electrode gap to burner 3 to 4mm Flame failure electrode (4213 078 52641).Height from heater base to centre of electrode 27.0±0.5mm. Front loading resistance sensing tumble dryer with gas heating.Reverse action drum tumble.Electronic control. 2-temperature exhaust thermostat control.
INSTALLATION 5 POSITION OF DRYER AND CONNECTIONS 1INSTALLATION The dryer is designed for installation using a flexible gas connection with tubing in accordance with B.S.669. Ensure that the supply gas sizing is adequate. When installing, position the appliance so that the plug is accessible. An electric supply cord with moulded-on 13 Amp.plug is fitted at the back of the dryer.The length is 1.5 m.(5ft.).
6. OPERATIONAL CHECK 6.1 Remove the pressure test point screw from the gas tee connection at the back of the dryer and connect a gas pressure gauge. 6.2 Check that the dryer control is in the 'off' position, and that the heat switch is set to 'high'. Remove anything from inside the drum, check that the lint filter is fitted, shut the dryer door. 6.3 Turn on the gas, push the electric plug into the socket and switch on the electricity supply. 6.4 Select program 9 (Timed). Check for ignition.
SERVICE INSTRUCTIONS RECOMMENDATIONS FOR DISMANTLING Note:Re-assembly should be done in reverse sequence to these instructions. Terminal Block (28),Control Unit (10),Button Assy (352), Heat Switch, Micro-Switch Assembly (248),Control Panel (353). Withdraw 3 screws from the back flange of the Table Top Assy.(386) and lift and move it rearwards for removal. This gives access to the 2-screws securing the Control Unit Bracket (11) to the top flange of the Cabinet.
Withdraw the 3-screws and shakeproof washers (13) securing the Flame Tube Assy.(34) to the Cabinet Base. Note:On re-assembly the shakeproof washers must be replaced to ensure a good earth connection. Lift out the Heater Assy. To remove either solenoid coil (45 or 45A) disconnect the electrical connectors, unscrew the nut (44). To remove the sensing electrode (33), withdraw the screw (41) lockwasher (482) and nut (411) securing it to the Flame Tube Assy.(34).
552 377 233 213 235 372 218 249 217 219 232 353 211 352
ECO 86A_ Exploded View 2 38 144 408 409 410 411 141 28 398 15 16 17 389 375 375 393 143 13 18 375 20 14 23 21 22 412 375 19 24 25 26 27 25 403 396
ECO 86A_ EXPLODED VIEW 3 455 454 248 440 441 442 445 446 447 456 458 459 445 448 356 250 229 29 30 32 31 406 13
ECO 86A Exploded View 4 270 266 439 444 466 477 467 468 438 465 463 464 " % = # "! "
ECO 86A Exploded View 5 41 33 482 411 45 375 39 31 406 13 32
ECO 86A Item 10 11 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 38 39 41 45 101 101a 112 125 141 142 143 144 196 199 201 203 203a 211 213 217 218 219 229 232 233 235 248 249 250 266 270 Description Control Unit Control Unit Bracket Assembly Screw M4 x 10 Rear Seal Assembly External Feed Pipe (Bundy Tube Assy 3) Gas Inlet Connector Restrainer Plate Rear Banjo Cover Plate (access) Hot Air Elbow Assembly Air Channel/lnsulating Plate Assembly Air Guide Cable Clip Back Panel Assembly Grommet
ECO 86A 352 353 354 356 359 362 363 364 365 366 367 369 370 372 374 375 376 377 386 387 389 393 394 396 398 403 406 407 408 409 409 410 411 412 427 432 438 439 440 441 442 444 445 446 447 447/1 448 451 454 455 456 458 459 463 464 465 Button & Knob Clip Assembly ( 4213 078 48961 & 4213 177 04871) Control Panel Assembly Locator Peg 6G*3/8 DP/PWABE/NIBS/TSZPC Hinge Assembly Window Door Frame Latch Pivot Latch Spring Door Latch Switch Strike Loom Clip Latch Guide Switch/Timer Bracket Pan Screw St M3 x 5 6 x 3
ECO 86A 466 467 468 477 482 537 552 555 556 Ring Spring Sensing Strip Sensing Strip Clip Ring Spring Plug M4 Toothed Lockwasher W’ Button (access cover) Neon Rear Panels Seal Kit HT Lead Bearing Pads & Brush Seal Kit which consists of key items Numbers 441, 442 & 445 Manufactured By: Crosslee plc, Halifax Road, Halifax, W. Yorks.
