AUTOMATIC ICE MAKER Use and Care Guide Ice Thickness Control H Cycle or Service Switch / Model and Serial Number (inside, not shown) Plate Bin Grille Part No. 756637 Rev.
BEFORE OPERATING THE ICE MAKER It is your maker: responsibility to make sure that . the ice . * has oeen installed where it is protected from the elements, * is located so that the front is not blocked to restrict incoming or discharge air flow. * is properly leveled. 0 is located in a well ventilated area with temperatures above 55°F (13°C) and below 110°F (43°C). Best results are obtained at temperatures between 70°F (21°C) and 90°F (32°C). is properly connected to a water supply and drain.
To 3perate the Ice Maker: 1 Select ice thickness (Figure 1). The ice maker has been pre-set to produce ice approximateiy ‘;” thick, while operating in a room ambient of 70’F (21°C). Operation in different ambient renuire readjusting the control 01. “THIN.” I temperatures may toward “THICK” ICE THICKNESS CONTROL SERVICE OR CYCLE SWITCH FIGURE Best 5,‘8” operation thick. will be obtained with ice l/2” 1 to 2. To start the normal ice making or cycle switch to “ON.
ING AND SANITIZING THE ICE MAKING SYSTEM Ice makkny system: : [-,p, r:1111;3rals rejected from the circulating water ~i:~~~;ri:! the freezing cycle wili eventually form a f,a:c! .;CJi'*j deposit in the water system which pre,,t:.;rj a ;spid release of the ice. i.ri-a:i 1c.e ;:i:,C; water system periodically to remove :i.ie’a, 3i: li I ” build-up. Frequency of cleaning &per& on ‘water hardness. With soft water, clean!I:!% I:~ay not be required for several years. With ‘~;~ro Ni2:t)r (15 to 20 grains/gal.
Removal and cleaning Do not operate unit of interior with panels components: 5. Wash the interior components you have just removed with mild soap or detergent and warm water. Rinse in clean water. Sanitize in a solution of l/402. (8 ml) of chlorine laundry bleach mixed with 1 gallon (3.8 L) warm water. removed. -- I NOTE: Do not wash plastic Plastic parts can not withstand 145” F (63°C). parts in dishwasher. temperatures above 6.
CHANGING THE BIN DOOR PANEL You can easily on the storage Blark, Almond, change the color of the front panel bin door. Four colors are available; Harvest Gold and White. 5. Replace To _~change -~-.___the panel : 1. Ooen the bin door. top cjf the door, which 2. Remove 3; C~reiully pane Is with 4. Choose the color you want to show and carefully slide the panels back into the door, being careful not to scratch the panel as it’s inserted. Remove the two hold the handle.
IF YOU NEED SERVICE OR ASSISTANCE, WE SUGGEST YOU FOLLOW THESE FOUR STEPS: I = Before calling for assistance. Performance can find yo:~ probler ns often result and fix yourself. from little . . things 3. Unit * Service position. D Check or to see that 0 Check for in electrical * cord be in is plugged blown fuse or tripped supply to machine. runs but produces 0 Service position.
2. If you need assistance*. . . Call Whirlpool COOL-LINE@ service assistance telephone number. Dial free from: Continental U. S. . . . . . (800) 253-1301 Michigan . , . , . . . . . . , . . (800) 632-2243 Alaska & Hawaii . , . . , . . (800) 253-l 121 and talk with one of our trained Consultants. The Consultant can instruct you in how to obtain sa:.isfactory operation from your appliance or, if service is necessary, recommend a qualified service company in your area. 3. If you need service* . . .
