0808_GB_42 Instructions for installation, use e maintenance ELECTRIC FRY TOP ADN 652 · ADN 653 ADN 654 · ADN 655 ADN 636 · ADN 637 ADN 638 · ADN 639 04/2008
CHARACTERISTICS Supplied by: Date: Customer Service: FAX e-mail 0808_GB_42 - ELECTRIC FRY TOP 04/2008 2 · 12
INDEX 1 Diagram 4 2 Features of the appliances 5 3 Technical data 5 4 Installation instructions 4.1 Safety rules 4.2 Structure, framework and safety devices of the appliances 4.3 Assembly 4.3.1 Installation premises 4.3.2 Statutory regulations and technical requirements 4.3.3 Installation 4.3.4 Electrical connection 4.3.5 Equipotential 6 6 6 6 6 6 6 6 6 5 Operation preparation 5.1 Preparation and Start-up 5.1.1 Start-up 5.1.2 Operator training 5.2 Maintenance 5.
1 - DIAGRAM ADN 652 ADN 653 ADN 654 ADN 655 600 600 0 0 0 15 0 25 25 15 240.
2 - CHARACTERISTICS OF THE APPLIANCES These appliances are used for professional purposes. Installation, repair and use must be carried out by expert personnel. The data plate is located on the appliance and contains all the data needed for installation. Beware of inexpert handling.
4 - INSTALLATION INSTRUCTIONS 4.1 Safety rules 4.3.2 Statutory regulations and technical requirements • Only a local gas utility technician is authorized to carry out gas installations and connections. The statutory regulations (applied in Germany VDE, Austria ÖVE, Switzerland SEV, etc.) and connection conditions performed by the gas utility must be strictly observed.
5 - SET-UP FOR OPERATION 5.1 Preparation and Start-up 5.3 Replacing parts Before starting up the appliance, remove the protective wrapping. Then carefully clean the working surface and the external parts with lukewarm water and detergent, using a damp rag to remove all traces of anti-rust material applied in the factory, then dry with a clean cloth. Protect cooking plate with oil or grease.
6 - INSTRUCTIONS FOR USE 6.4.2 What to do in case of prolonged period of disuse Fig. 1 When the appliance is not to be used for a long time, clean thoroughly, cas instructed in the chapter 6.5 “Appliance care and frequency of maintenance”, switch off any electric power. 50 0 6.5 Appliance care and frequency of maintenance 2 100 300 0 0 15 25 3 200 1 6.
6 - INSTRUCTIONS FOR USE 6.6.2 Warnings and advice for maintenance of “stainless steel” appliances • “Stainless” steel equipment surfaces must be kept clean and in contact with air at all times. When not running, keep appliance doors open so as to allow air to run through it. • Regularly remove calcium , grease, starch, and egg white deposits where rust may build up if there is lack of air. Do not use bleaching products or products containing chloride.
7 - APPENDIX: ELECTRICAL DIAGRAMS ADN 652 • ADN 653 ADN 636 • ADN 637 R1 R1 1 H2 R1 3 4 2 5 6 H1 F2 1 2 3 4 11 21 31 B1 F1 P1P2 P3 P4 mA 1 2 3 4 5 12 22 32 6 R1 1 2 3 4 5 6 mA 1 2 400V 3 N L1 L 2 L 3 N PE PE L1 L 2 L 3 12 3 4 22 5 6 32 4 230V 3 mA B1 F1 H1 H2 R1 F2 Terminal board Switch Thermostat Green indicator light Yellow indicator light Heating element 1250 W Safety thermostat Total power: 3.
7 - APPENDIX: ELECTRICAL DIAGRAMS ADN 654 • ADN 655 ADN 638 • ADN 639 R1 R1 1 H2 R1 3 4 2 5 R1 6 7 8 H1 12 22 32 F2 11 21 31 1 2 3 4 11 21 31 B1 F1 P1P2 P3 P4 mA 1 2 3 4 5 12 22 32 6 R1 1 2 3 4 5 6 mA 1 2 400V 3 N L1 L 2 L 3 N PE 12 L1 L 2 L 3 3 4 22 5 6 7 8 32 PE 230V 3 mA B1 F1 H1 H2 R1 F2 Terminal board Switch Thermostat Green indicator light Yellow indicator light Heating element 1250 W Safety thermostat Total power: 5.
WARNING THE MANUFACTURER CANNOT BE HELD RESPONSIBLE FOR ANY INACCURACIES IN THIS BOOKLET DUE TO COPYING OR PRINTING ERRORS. DUE TO ITS POLICY OF CONTINUAL PRODUCT IMPROVEMENT, THE MANUFACTURER RESERVES THE RIGHT TO MAKE ANY CHANGES DEEMED NECESSARY. THE MANUFACTURER CANNOT BE HELD RESPONSIBLE IF THE INSTRUCTIONS CONTAINED IN THIS MANUAL ARE NOT OBSERVED. WHIRLPOOL EUROPE srl V.
