0804_GB_42 Instructions for installation, use e maintenance GAS FRY TOP ADN 632 · ADN 633 ADN 634 · ADN 635 04/2008
CHARACTERISTICS Supplied by: Date: Customer Service: FAX e-mail 0804_GB_42 - GAS FRY TOP 04/2008 2 · 12
INDEX 1 Diagram 4 2 Characteristics of the appliances 5 3 Technical data 5 4 Installation instructions 4.1 Safety rules 4.2 Structure, framework and safety devices of the appliances 4.3 Assembly 4.3.1 Installation premises 4.3.2 Statutory regulations and technical requirements 4.3.3 Installation 4.3.4 Gas connection 4.3.5 Smoke extraction 6 6 6 6 6 6 6 6 6 5 Operation preparation 5.1 Preparation and Start-up 5.1.1 Start-up 5.1.2 Check of power 5.1.3 Checking the input pressure 5.1.
1 - DIAGRAM ADN 634 ADN 635 ADN 632 ADN 633 700 400 60 400 Gas 1/2" Gas 1/2" 0 150 657 678 0 45 510 34 45 Gas 1/2" 45 545 38 55 Data plate 34 700 Data plate 600 34 45 Gas 1/2" 700 34 310 Data plate 400 0804_GB_42 - GAS FRY TOP 04/2008 4 · 12
2 - CHARACTERISTICS OF THE APPLIANCES These appliances are used for professional purposes. Installation, repair and use must be carried out by expert personnel. These instructions for installation are for our gas fry top set up for the category in the table 1 on pag. 5. The data plate is located on the appliance, see diagram. Beware of inexpert handling.
4 - INSTALLATION INSTRUCTIONS 4.1 Safety rules 4.3 Assembly • Only a local gas utility technician is authorized to carry out gas installations and connections. The statutory regulations (applied in Germany VDE, Austria ÖVE, Switzerland SEV, etc.) and connection conditions performed by the gas utility must be strictly observed.
5 - SET-UP FOR OPERATION 5.1 Preparation and Start-up Before starting up the appliance, remove the protective wrapping. Then carefully clean the working surface and the external parts with lukewarm water and detergent, using a damp rag to remove all traces of anti-rust material applied in the factory, then dry with a clean cloth. Protect cooking plate with oil or grease. 5.1.1 Start-up Before using the appliance for the first time, thoroughly clean out the griddle (see the chapter 6.
5 - SET-UP FOR OPERATION 5.1.5 Power check for operation with liquid gas 5.1.9 Conversion and adjustment Check if the type of injectors used meet the data of the table 1. Check that the pressure reducer installed in the system has an outlet pressure which is compliant with paragraph 5.1.2 "Check of power" (can be checked on the data plate of the appliance or on the table 1).
5 - SET-UP FOR OPERATION After the replacement check the seal using a leack detector spray. 5.3.5 Burner fry top 600 Unscrew the screws (pos. 2 and 5 fig. 2B) fixing the burner to the injector-holder collector nuts (pos. 4 fig. 2B) and on the combustion chamber, lift up the burner (pos. 3 fig. 2B) for pull off from injectorholder collector, pull off and put in a new piece in the reverse order. After the replacement check the seal using a leack detector spray. 5.1.
6 - INSTRUCTIONS FOR USE 6.1 Safety, cleaning and repair rules Special precautions • This appliance is used for the preparation of meals at industrial level. Usage and cleaning can be carried only by expert personnel. Maintenance and repair can be carried out only by skilled technical personnel. • These indications must be communicated to all those concerned during internal training. • Attention! This appliance must be constantly watched over when being used! • Grease and overheated oil can catch fire.
6 - INSTRUCTIONS FOR USE 6.6 Recommendations for the treatment of stainless “steel industrial” kitchens soaps or fine-grained sand paper. Larger rust spots can be removed with 2-3% of hot oxalic acid solution. If these cleaning products do not do the job, a nitric acid (10%) treatment is required. Attention! These treatments can be carried out only by expert personnel according to current regulations! 6.6.
WARNING THE MANUFACTURER CANNOT BE HELD RESPONSIBLE FOR ANY INACCURACIES IN THIS BOOKLET DUE TO COPYING OR PRINTING ERRORS. DUE TO ITS POLICY OF CONTINUAL PRODUCT IMPROVEMENT, THE MANUFACTURER RESERVES THE RIGHT TO MAKE ANY CHANGES DEEMED NECESSARY. THE MANUFACTURER CANNOT BE HELD RESPONSIBLE IF THE INSTRUCTIONS CONTAINED IN THIS MANUAL ARE NOT OBSERVED. WHIRLPOOL EUROPE srl V.
