Side-by-Side Refrigerator l/4” Trim Kits 4370076,4370077, < and 4370070 Installation Instructions
Important Do not discard dispenser trim or instructions. Decorator Door Panel Installation Instructions 2. Dispenser Models Remove crushed/cubed ice switch cover on dispenser by placing taped edge of putty knife underneath cover and pulling out. Release bottom clips on dispenser cover by placing taped edge of putty knife underneath cover and pulling out. Release top clips by holding bottom of dispenser cover out and sliding up.
Contents Decorator Introduction .. ...... ............... ......... ...... ....... ...... .... ....... Decorator Panel Dimensions .. .... .... ....... ................ ... Parts List ..... .......... ........... .............-.......................... Procedure .............. ..................... ..........................-... 2 2 2 3 Panel Dimensions Listed below are required height x width dimensions for decorator panels. Panels are not supplied with this kii and can be purchased locally.
Procedure 6. InstaY new top handle end caps by pladng on handles. Insert and tighten screws. 7. Replace dispenser cover by snapping in place. Replace switch cover by snapping in p&e. 6. Remove toe grille by pulling fomard. Important Save all screws and reuse in original location. 1. Remove top handle end caps by removing screws. 2. Remove cn~~hedkubed ice switch cover on dispenser by pulling forward.
16. Tape doors shut using masldng tape. Caution To avoid property damage, drain water from water tube into small bucket. 12. Loosen water tube clamp screw. Loosen plastic water tube union nut. Gently pull water tube away from union nut and through tube damp. Failure to do so can resutf in death or electrical shock. 17. Replace top hinges by placing top hinges on refrigerator. Insert and tigMen screws. Raoonnect top hinge wire connectors by snapping together.
24. Push water tube into plastic union nut and tighten union nut by hand. Gantly pull on tuba to confirm nut is tight. Tighten water tube clamp screw. Caution To avoid property damage, confirm water tube union nut is secure before replacing toe grille. 25. Replace toe grille by inserting clips n holes and snapping in.
--
INSTALLATION INSTRUCTIONS ftJTRODUCTlON PARTS UST Thg Penmerer Trim Kit artaches as a ‘trame”lc free-standing :ef:lgeraIcrs and IS deslgned lo grvc a built-In look when cabineis are lccared above and on bolh sides. i DESCRIPTION ) BllD PN ! 8171 P’N j 6; ) 6ea~anOrhcr=ugnlyunasrrlaMfhlsn~ire1nstruc~lsnm;nuai before s:anrng lo install the Permeter Trim Ki!.
INSTALLATION INSTRUCTIONS _I. Ir4TRODUCTlON PARTS LIST The Penmeter Trim Kti anaches as a ‘?rame”lo free-standing :ef:lgerators and IS deslgnti lo gave a built-In lank when cabiners are lccared above and on borh sides. i OESCRlPllON ) El10 P.N 1 El11 P:N ) CT ) F.ca~anorhorolrgnlyund~rsra~thlsclnrlre~n=tnxtlsnm;nual before stanq to install Ihe Penmeter Trim Kit.
INSTALIATION INSTRUCTIONS C. Slide gusset on lett frame mto channel on top k3arr 7. Checkposit~onoftopframeandinslaIlonrefrigeratortop. A. Belore removing paper backing from veicro patches of top frame. be sure to center trame between hinge covers at lop of refrigerator cabinet. Front flange of frame must fit snugly against front face of refrigerator cabinet. 8.
:. ‘._ s.. 9. -. -, _” - _.’ 131Iv w’~u m I I rcnww lNSTALIATlON Check top frame for correct center position. A. If top frameneedscentering,or to gain access to top I tinges for door remuvaVhinge adjustment: Ioosen 5132 inch bezelgussel machine screws in left and right frames. 6. Gently pull on lop kme to separate velcro patches and slide top frame up and away from refrigerator. 10. Roll refrigerator into place to check leveling and proper fit with surrounding cabmets. 11.
