Product Manual

Page 3
ORG - AUX IN
*Max. Peak Current Draw = 6.0A
YEL - AUX OUT*
RED - to +12VDC (Fuse @ 10A)
BLK - to Chassis Ground
12
3
4
5
6
78
910
1-BRN2-RED
3-ORG4-YEL
5-GRN
6-BLU
7-VIO
8-GRY
9-WHT10-WHTWIRING DIAGRAM
Important!
When properly oriented
the cable will exit the
end of the extrusion, as shown.
Left
Pin Housing
(Rear View)
12
11
13 14
1
7
9
8
2
10
3
4
5
6
8
1
ITEM PART NUMBER DESCRIPTION
SCREW, #8 X 1 PPHSMS
DIVIDER, LENS TAC8
LIGHTHEAD, TAC8, AMBER
GASKET, ENDCAP
ASSY, INPUT HARNESS (w/ENDCAP)
ENDCAP, w/o HOLE TAC8
SCREW, #6-32 X 1/2 PPH SS
SCREW, #10-24 X 3/4 HEX HDMS SS
SPACER
WASHER, #10 FLAT SS
NUT, #10-24 ELASTIC STOP
HOUSING, 10-POS PIN
CONTROL HEAD, TAC8
HARNESS, TAC8 INPUT ADAPTER
3 8 - 0 4 6 F 8 9 8 - 0 0
0 1 - 0 2 6 F 8 2 8 - A 0
3 8 - 0 2 6 F 8 9 7 - 0 0
4 6 - 0 7 6 F 4 0 9 - * *
11 - 2 8 7 7 8 7 - 0 0 0
2 0 - 0 0 2 3 6 2 7 - 0 0
3 9 - 0 4 1 0 3 1 3 - 0 4
0 1 - 0 6 6 F 8 2 9 - 0 0
4 6 - 0 7 4 7 6 0 7 - 0 0
QTY
1
1
1
1
1
4
4
4
4
4
9
2
3
11
12
13
4
5
6
7
8
9
10
19
4 6 - 0 7 6 F 4 0 9 - * *
20 = 20’ Cable
35 = 35’ Cable
55 = 55’ Cable
Auxiliary Out
The Auxiliary Out wire (Yellow), when activated, can provide +12VDC,
allowing the TAC8 to activate an auxiliary device with a maximum peak
current draw of no greater than 6.0 Amps. Pressing the ‘A’ button on the
control head manually activates and deactivates the Aux Out feature (refer
to the Auxiliary In section for Override information).
Auxiliary In
The Auxiliary In wire (Orange) can be connected to a +12VDC signal to
allow that signal to activate and deactivate the Aux Out wire. The Aux In is
an override signal that functions regardless of the Aux Out button on the
control head. As long as the Aux In wire is receiving a +12VDC signal, the
Aux Out wire will be active.
Traffic Advisor Sequence List
1 Solid
2 On/Off
3 On/Off (with Flicker)
4 On/Off Double Sweep
5 1 Lamp Double Sweep
6 1 Lamp (with Flicker) w/ End Comet
7 3 Lamp
8 2 Lamp
9 1 Lamp
Flash Pattern List
1 ZigZag
2 Comet Flash® Left/Right Alternating
3 SignalAlert™ Simultaneous
4 SignalAlert In/Out Alternating
5 ModuFlash™
6 ActionScan™
7 Single Flash 375
8 Single Flash 150
9 Single Flash 75
Service:
To replace a lighthead,
begin by turning off the
power. Remove the
retaining screw and lens
divider from either side of
the appropriate lighthead.
The lighthead may now be
pulled away from the
extrusion and disconnected
from the wiring harness.
Reverse this procedure to
install the replacement
lighthead.
IMPORTANT! It is the
responsibility of the
installation technician to
make sure that the
installation and operation
of this product will not
interfere with or
compromise the operation
or efficiency of any
vehicle equipment!
IMPORTANT! Before returning this vehicle to active service, visually
confirm the proper operation of this product, as well as all vehicle
components/equipment.
CAUTION! DO NOT LOOK DIRECTLY AT THESE LED’S WHILE THEY ARE ON.
MOMENTARY BLINDNESS AND/OR EYE DAMAGE COULD RESULT!
I M P O R T A N T W A R N I N G !