Instruction manual

P84905-001 G
Sheet 26 of 37
Example 7: IN>OUT SYNC MODE from CODED INPUT SOURCE (CLASS A)
JUMPER WIRE
FOR UNUSED OUTPUT
FACP
NAC
CIRCUIT
10K OHMS
EOLR
OR EOLR (10K OHMS)
TO NEXT APPLIANCE
FACP
NAC
CIRCUIT
RETURN
EOLR COMPATIBLE
WITH FACP
TO FACP
SUPERVISORY
NAC
IN1
IN2
CC1
CC2
SBUS
IN
SBUS
RET
SIL
IN
RET1
RET2
COM
NO
NC
TROUBLE
AUX
OUT
NAC1
OUT
NAC2
OUT
NAC3
OUT
NAC4
OUT
TB1
TB2
TB6
TB3
TB4
SW2
SW1
SW3
SW4
IN2 FOLLOWER OFF/ON
TROUBLE LATCH OFF/ON
SBUS IN1/IN2
GF DETECT ON/OFF
SBUS SYNC/TEMPORAL
SYNC PROTOCOL
SYNC PROTOCOL
NAC1-NAC2 CLASS A/B
NAC3-NAC4 CLASS A/B
AUX POWER CP/MP
SBUS MASTER/REMOTE
NAC4 SYNC/ TEMPORAL
NAC4 IN1/IN2
NAC3 IN1/IN2
NAC2 IN1/IN2
NAC1 IN1/IN2
IN1 FOLLOWER OFF/ON
SW6
NAC3 SYNC/ TEMPORAL
NAC2 SYNC/ TEMPORAL
NAC1 SYNC/ TEMPORAL
D30
IN2
D31
D36
INPUT1
INPUT2
D38
SILENCE
D2
GENERAL TROUBLE
D37
ACTIVE
SW5
D40
D3: GROUND FAULT TROUBLE
D4-D8: SEE
TAB L E 9
< D8-D4 >
SYNC BUS
GROUND FAULT
LOCATOR
D9
POWER
D1
IN1 TROUBLE
X
Minimum pulse duration for coded signals must be greater than 0.25 seconds.
CAUTION: Only use audible appliances that can use a coded signal. Do not use with Wheelock Series AS/AH, NS/NH
or HS4/HS appliances.
Note: To monitor trouble in Class A Mode, only use the “COM”, “NC” and “NO” terminals.
Example 8: WHEELOCK SYNC MODE with Audible Silence (CLASS A)
JUMPER WIRE
FOR UNUSED OUTPUT
FACP
NAC
CIRCUIT
10K OHMS
EOLR
OR EOLR (10K OHMS)
TO NEXT APPLIANCE
FACP
NAC
CIRCUIT
RETURN
EOLR COMPATIBLE
WITH FACP
TO FACP
SUPERVISORY
NAC
IN1
IN2
CC1
CC2
SBUS
IN
SBUS
RET
SIL
IN
RET1
RET2
COM
NO
NC
TROUBLE
AUX
OUT
NAC1
OUT
NAC2
OUT
NAC3
OUT
NAC4
OUT
TB1
TB2
TB6
TB3
TB4
SW2
SW1
SW3
SW4
IN2 FOLLOWER OFF/ON
TROUBLE LATCH OFF/ON
SBUS IN1/IN2
GF DETECT ON/OFF
SBUS SYNC/TEMPORAL
SYNC PROTOCOL
SYNC PROTOCOL
NAC1-NAC2 CLASS A/B
NAC3-NAC4 CLASS A/B
AUX POWER CP/MP
SBUS MASTER/REMOTE
NAC4 SYNC/TEMPORAL
NAC4 IN1/IN2
NAC3 IN1/IN2
NAC2 IN1/IN2
NAC1 IN1/IN2
IN1 FOLLOWER OFF/ON
SW6
NAC3 SYNC/TEMPORAL
NAC2 SYNC/TEMPORAL
NAC1 SYNC/TEMPORAL
D30
IN2
D31
D36
INPUT1
INPUT2
D38
SILENCE
D2
GENERAL TROUBLE
D37
ACTIVE
SW5
D40
D3: GROUND FAULT TROUBLE
D4-D8: SEE
TAB L E 9
< D8-D4 >
SYNC BUS
GROUND FAULT
LOCATOR
D9
POWER
D1
IN1 TROUBLE
X
 This mode will only synchronize Wheelock horns, horn strobes, and strobes with the synchronization capability.
 When the Silence (SIL) terminals receive a NAC voltage, silence-able horn outputs connected to IN1 and/or IN2
will be silenced.
Note: To monitor trouble in Class A Mode, only use the “COM”, “NC” and “NO” terminals.