Instruction manual

P83259 H
Sheet 16 of 26
Table 11A: Single Zone Dial Access Codes
Master Remote 1 Remote 2 Remote 3 Remote 4 Remote 5
Main* 1/001 13/013 25/025 37/037 49/049 61/061
Board 2/002 14/014 26/026 38/038 50/050 62/062
3/003 15/015 27/027 39/039 51/051 63/063
4/004 16/016 28/028 40/040 52/052 64/064
Position 1 5/005 17/017 29/029 41/041 53/053 65/065
6/006 18/018 30/030 42/042 54/054 66/066
7/007 19/019 31/031 43/043 55/055 67/067
Position 2 8/008 20/020 32/032 44/044 56/056 68/068
9/009 21/021 33/033 45/045 57/057 69/069
10/010 22/022 34/034 46/046 58/058 70/070
Position 3 11/011 23/023 35/035 47/047 59/059 71/071
12/012 24/024 36/036 48/048 60/060 72/072
Table 11B: Single Zone Dial Access Codes (Continued)
Remote 6 Remote 7 Remote 8 Remote 9 Remote 10 Remote 11
Main* 73/073 85/085 97/097 109/109 121/121 133/133
Board 74/074 86/086 98/098 110/110 122/122 134/134
75/075 87/087 99/099 111/111 123/123 135/135
76/076 88/088 100/100 112/112 124/124 136/136
Position 1 77/077 89/089 101/101 113/113 125/125 137/137
78/078 90/090 102/102 114/114 126/126 138/138
79/079 91/091 103/103 115/115 127/127 139/139
Position 2 80/080 92/092 104/104 116/116 128/128 140/140
81/081 93/093 105/105 117/117 129/129 141/141
82/082 94/094 106/106 118/118 130/130 142/142
Position 3 83/083 95/095 107/107 119/119 131/131 143/143
84/084 96/096 108/108 120/120 132/132 144/144
Legend: Zones/Access Code
Example: 7/007 = Zone 7, dial access code 007
*The MZC-RM does not use these single zone dial access codes.
10. INSTALLATION INSTRUCTIONS
:
1. Remove MZC-144 cover.
2. Disconnect power.
3. Select the position which the MZC-RM is to be plugged into from Table 11A and 11B (e.g.: if you want the MZC-RM to
be zones 7, 8 or 9 on the MZC-144, the MZC-RM would be installed in Position 2 on the MZC-144 board).
4. Plug MZC-RM into its selected position (See Figure 10).
CAUTION: Plugging the MZC-RM in backwards can result in improper operation and failure of the unit.
5. Set 2 configuration jumpers in accordance with Figure 15.
6. Connect relay outputs as required (See Figure 15).
7. Re-apply power to unit.
8. Re-install MZC-144 cover.
CAUTION: These devices are not intended for use in hazardous locations as defined by the National Electrical Code (NEC).