Installation guide

- 6 - AL602ADA220J
Terminal Identification Table:
AL600ADA Power Supply Board*
Terminal Legend Function/Description
L,G,N
 Connect220VACtotheseterminals:Ltohot,Ntoneutral.
 -DC+  24VDC@6.5ampinalarmnonpower-limitedoutput.
 ACFAIL
 NO,C,NC
 Form“C”drycontactsusedtoinstantaneouslysignalthelossACtolocalannunciation
 devices,withACpresentterminalsmarkedNOandCareopen,NCandCareclosed. 
 WhenlossofACoccursterminalsmarkedNOandCareclosed,NCandCareopen.
 ACLOCAL
 NC,NO,C
 Form“C”drycontactsusedtoinstantaneouslysignalthelossACtolocalannunciation
 devices,withACpresentterminalsmarkedNOandCareopen,NCandCareclosed. 
 WhenlossofACoccursterminalsmarkedNOandCareclosed,NCandCareopen.
 BATFAIL
 NO,C,NC
 Form“C”drycontactsusedtosignallowbatteryvoltageorlossofbatteryvoltage.
 UndernormalconditionsterminalsmarkedNOandCareopen,NCandCareclosed. 
 DuringatroubleconditionterminalsmarkedNOandCareclosed,andNCandC
 areopen(Fig. 2, pg. 7).
 +BAT- Stand-bybatteryinput(leadsprovided)(Fig. 2, pg. 7).
*Power Board Parameter Specifications:
• ACFailconditionwillreportapproximately30secondsafterlossofAC.Todelayreportfor2.5to3hourscut
 jumperACDELAYonthePowerSupplyBoard(ACtroubleoutputdelayoption).IfthismodeisselectedthePower
 SupplyBoardmustberesetbyremovingallpowertoitfor30seconds.
• Lowbatteryconditionwillreportatapproximately21VDC.
• Batterypresencedetectionwillreportwithin180secondsafterbatteryremainsundetected(missingorremoved).
 Arestoredbatterywillreportwithin30seconds.
LED Diagnostics:
AL600ADA - Power Supply Board
Red (DC) Green (AC) Power Supply Status
ON ON Normaloperatingcondition.
ON OFF LossofAC,Stand-bybatterysupplyingpower.
OFF ON NoDCoutput.
OFF OFF LossofAC.Dischargedornostand-bybattery.NoDCoutput.
AL800LGK9E - Logic Board
LED OFF ON BLINK (LONG)* BLINK (SHORT)**
ON Normal AlarmCondition TroubleCondition TroubleConditionMemory
ON Normal AlarmCondition TroubleCondition TroubleConditionMemory
OFF Normal AlarmCondition TroubleCondition TroubleConditionMemory
OFF Normal AlarmCondition TroubleCondition TroubleConditionMemory
Input1 Normal AlarmCondition TroubleCondition ---
Input2 Normal AlarmCondition TroubleCondition ---
Fault Normal AlarmCondition --- ---
* Indicatescurrenttroublecondition.Whentrouble(open,shortorground)occursonaspecificoutput,the
 correspondingredoutputLED,[OUT1-OUT4]willblink.ThecorrespondinggreeninputLEDwill
 blinkaswell.Looptroublewillreportwithin30seconds.
**Indicatestroubleconditionmemory.Whenatroubleconditionrestores,theunitsredoutputLED,[OUT1-OUT4]
 willblinkwithashorteranddistinctlyadifferentduration.ThegreeninputLEDswillbeoff(normalcondition). 
 Toresetthememorydepresstheresetbutton(Fig. 2c, pg. 7).TheLED(s)willextinguish.
Note:Ifindicatingcircuitshavebeenrestored,memoryresetisnotrequiredfornormaloperationoftheunit.