GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL ASSEMBLY & OPERATOR MANUAL Grain Augers included in this manual: GHR80-31 GHR80-36 GHR80-41 GHR80-46 GHR 80-51 GHR 80-56 GHR 80-61 GHR 80-71 GHR100-31 GHR100-41 GHR 100-51 GHR 100-61 GHR 100-71 WHR80-31 WHR80-36 WHR80-41 WHR80-46 WHR 80-51 WHR 80-56 WHR 80-61 WHR 80-71 WHR100-31 WHR100-41 WHR 100-51 WHR 100-61 WHR 100-71 Read this manual before using product.
This product has been designed and constructed according to general engineering standardsa. Other local regulations may apply and must be followed by the operator. We strongly recommend that all personnel associated with this equipment be trained in the correct operational and safety procedures required for this product. Periodic reviews of this manual with all employees should be standard practice. For your convenience, we include this sign-off sheet so you can record your periodic reviews.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL TABLE OF CONTENTS 1. Introduction .......................................................................................................................... 5 2. Safety .................................................................................................................................... 7 2.1. General Safety Information ...................................................................................... 7 2.2. Assembly Safety...........
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL TABLE OF CONTENTS 6. Maintenance & Storage...................................................................................................... 49 6.1. General Maintenance Procedures.......................................................................... 49 6.2. General Storage Procedures.................................................................................. 50 7. Troubleshooting ...........................................................
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 1. INTRODUCTION 1. Introduction Thank you for purchasing a WHEATHEART grain auger. Before using, please read this manual and understand the various features of the equipment and precautions for efficient and safe operation. Keep this manual handy for frequent reference and to review with new personnel. A sign-off form is supplied on the inside front cover to record your safety reviews.
1.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 2. SAFETY 2.1. GENERAL SAFETY INFORMATION 2. Safety 2.1. GENERAL SAFETY INFORMATION The Safety Alert symbol identifies important safety messages on the product and in the manual. When you see this symbol, be alert to the possibility of personal injury or death. Follow the instructions in the safety messages. Why is SAFETY important? • Accidents disable and kill. • Accidents cost. • Accidents can be avoided.
2. SAFETY 2.2. ASSEMBLY SAFETY WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL YOU are responsible for the SAFE use and maintenance of your equipment. YOU must ensure that you and anyone else who is going to work around the equipment understands all procedures and related SAFETY information contained in this manual. Remember, YOU are the key to safety. Good safety practices not only protect you, but also the people around you. Make these practices a working part of your safety program.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 2. SAFETY 2.3. TRANSPORT & PLACEMENT SAFETY 2.3. TRANSPORT & PLACEMENT SAFETY • Transport auger in full down position with slight tension on cable. • Properly place hitch pin and securely attach safety chain. Use a type of hitch pin that will not allow auger to separate from towing vehicle. • Always attach an SMV (slow moving vehicle) sign before transporting auger. Equip the auger with the necessary lights for transportation where required by law.
2. SAFETY 2.4. OPERATION SAFETY WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL • Inspect lift cable before using auger. Replace if frayed or damaged. Make sure it is seated properly in cable sheaves and cable clamps are secure. • Operate auger on level ground free of debris. If ground is uneven, anchor the auger to prevent tipping or upending. • Augers are not insulated. Keep away from electrical lines. Electrocution can occur without direct contact.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 2. SAFETY 2.5. MAINTENANCE SAFETY Figure 2.1 2.5. MAINTENANCE SAFETY • Shut down and lock out all power before attempting maintenance of any kind. If applicable, disconnect PTO driveline from tractor or hydraulic hoses on units with hydraulic drive hoppers. • After maintenance is complete, replace and secure all safety guards and safety devices, and if applicable, service doors and cleanout covers.
2. SAFETY 2.6. PTO SAFETY WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL result. Use of unauthorized parts will void warranty. If in doubt, contact WHEATHEART or your WHEATHEART dealer. • Do not modify any auger components without authorization from WHEATHEART. Modification can be dangerous and result in serious injuries. 2.6. PTO SAFETY • Never use a PTO driveline without a rotating shield in good working order. • Ensure PTO driveline is securely attached at both ends before operating.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 2. SAFETY 2.7. SAFETY DECALS DECAL #20807 WARNING To prevent serious injury or death: • Read and understand the manual before assembling, operating, or maintaining the equipment. • Only trained personnel may assemble, operate, or maintain the equipment. • Children and untrained personnel must be kept outside of the work area. • If the manual, guards, or decals are missing or damaged, contact factory or dealer for replacements.
2. SAFETY 2.7. SAFETY DECALS WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL DECAL #20819 DANGER DECAL #20817 DANGER ROTATING PTO DRIVELINE HAZARD To prevent serious injury or death: • Keep body, hair, and clothing away from rotating PTO driveline. • Do not operate equipment unless all driveline, tractor, and equipment shields are in place and in good working order. • Make certain the driveline shields turn freely on driveline. • Make certain the driveline is securely attached at both ends.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 2. SAFETY 2.7. SAFETY DECALS WARNING DECAL #20807 To prevent serious injury or death: • Read and understand the manual before assembling, operating, or maintaining the equipment. • Only trained personnel may assemble, operate, or maintain the equipment. • Children and untrained personnel must be kept outside of the work area. • If the manual, guards, or decals are missing or damaged, contact factory or dealer for replacements.
2. SAFETY 2.7. SAFETY DECALS WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL DANGER ELECTROCUTION HAZARD To prevent death or serious injury: • When operating or moving, keep equipment away from overhead power lines and devices. • Fully lower equipment before moving. This equipment is not insulated. Electrocution can occur without direct contact. 20817 Made in Canada DECAL #20817 DANGER ROTATING FLIGHTING HAZARD To prevent death or serious injury: • KEEP AWAY from rotating auger flighting.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 2. SAFETY 2.7. SAFETY DECALS DANGER ROTATING PTO DRIVELINE HAZARD To prevent serious injury or death: • Keep body, hair, and clothing away from rotating PTO driveline. • Do not operate equipment unless all driveline, tractor, and equipment shields are in place and in good working order. • Make certain the driveline shields turn freely on driveline. • Make certain the driveline is securely attached at both ends.
2. SAFETY 2.7. SAFETY DECALS WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL WARNING UPENDING HAZARD To prevent death or serious injury: • Anchor intake end and/or support discharge end to prevent upending. • Do not raise auger intake end above tow bar height. • Auger intake end must always have downward weight. Do not release until attached to tow bar or resting on ground. • Empty auger and fully lower before moving.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 3. ASSEMBLY 3.1. TUBES & FLIGHTING 3. Assembly WARNING Before continuing, ensure you have read and understand the relevant information in the safety section. Safety information is provided to help prevent serious injury, death, or property damage. Before beginning assembly, familiarize yourself with all the sub-assemblies and hardware making up the auger. Have all parts on hand and arrange them for easy access.
3. ASSEMBLY 3.1. TUBES & FLIGHTING WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 3. Slide tube sections together and secure. Make sure to align upper and lower track ends and then tighten bolts. Secure with hardware in table below. Important: Track ends must align to allow track shoe to smoothly slide over track joint. Misalignment may cause jamming. FOR 8” AND 10” AUGERS, SLIDE FLIGHTING TOGETHER. Figure 3.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 3. ASSEMBLY 3.2. TRACK SHOE & TRACK STOP 3.2. TRACK SHOE & TRACK STOP Auger Length 31’ 36’ 41’ 46’ 51’ 56’ 61’ 71’ From Discharge End 1. Slide roller track shoe onto track. 2. Attach the upper track stop with 7/16” x 1" bolts, heavy flat washers, and locknuts (Figure 3.5). For correct positioning of the upper track stop, see Table 3.1. 3. Attach the lower angle-iron track stop (on 36’, 56’, and 61’ augers) with two 7/16” x 1" bolts and locknuts.
3. ASSEMBLY 3.3. INTAKE HITCH WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL Auger Length 31’ 36’ 41’ 46’ 51’ 56’ 61’ 71’ From Intake End Table 3.2 Lower Track Stopsa Lower Track Stop Locations Welded 1st Hole 2nd Hole Trackstop 8”-10” 8” 8”-10” 8” 8”-10” 8” 8”-10” 8”-10” a. Count from the lower intake end of auger. For example, “1st Hole” refers to the first set of holes in the lower end of the track nearest the intake end. 3.3. INTAKE HITCH 1.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 3. ASSEMBLY 3.5. SHAFT DRIVE GEARBOX 3. Slip lower driveshaft segments through bearings on lower tube section. Install a Woodruff key, and slide into shaft connector. • Driveshafts on 10" x 51’, 61’, and 71’ augers require a square key. 4. Place a few drops of oil at each driveshaft bearing to allow for break-in. 5. Tighten all set screws on shaft connectors. Table 3.
3. ASSEMBLY 3.5. SHAFT DRIVE GEARBOX WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 2. Place gearbox assembly on auger tube, leaving a minimum 1/16” clearance between chain coupler sprockets. 3. Secure gearbox assembly to auger tube with half-tube clamps and four 7/16” x 1" bolts and locknuts. Figure 3.7 Figure 3.8 GEARBOX MOUNTING PROCEDURE FOR THE FOLLOWING AUGERS • 8" x 56’-61’-71' • All 10" augers These augers are equipped with chain couplers (pre-installed on gearbox). See Figure 3.9.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 3. ASSEMBLY 3.6. LEFT HAND PTO DRIVE Figure 3.9 3.6. LEFT HAND PTO DRIVE To change auger from a right-hand drive to a left-hand drive as seen when standing at intake end facing the discharge end, proceed as follows: Note: Important: 30641 R1 1. Remove the gearbox guard and the connector/coupler guard and set aside. Where applicable, remove the coupler chain. 2. Remove the gearbox from mount and place on side (with input shaft pointing up). 3.
3. ASSEMBLY 3.7. PTO DRIVESHIELD WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 3.7. PTO DRIVESHIELD Note: 1. Clean paint and dirt from gearbox shafts and inside driveline yokes. 2. Slide non-spline end of PTO driveline onto input shaft on gearbox using a 1/4” x 1-1/2” square key. Tighten set screws securely. The PTO driveline is non-separable type. Do not extend beyond 80". 3.8. DRIVESHAFT SHIELD ALL 8" AUGERS UP TO AND INCLUDING 8" X 51': See Figure 3.7 and 3.8. 1.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 3. ASSEMBLY 3.9. DISCHARGE SPOUT Table 3.5 Driveshaft Shielding Sequence Auger Size/ Length 8” x 31’ 8” x 36’ 8” x 41’ 8" x 46’ 8" x 51’ 8" x 56’ 8" x 61’ 8" x 71’ 10" x 31’ 10" x 41’ 10" x 51’ 10" x 61’ 10" x 71’ Step 1 Qty Length 42” 1 (1.07 m) 42” 1 (1.07 m) 42” 3 (1.07 m) 42” 5 (1.07 m) 42” 2 (1.07 m) 42” 2 (1.07 m) 48” 1 (1.22 m) 42” 4 (1.07 m) 42” 1 (1.07 m) 48” 1 (1.22 m) 48” 11 (1.22 m) 48” 1 (1.22 m) 42” 4 (1.
3. ASSEMBLY 3.10. SPROCKET HEAD GEARING WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 3.10. SPROCKET HEAD GEARING Change the upper drive sprockets on the following augers: To obtain the correct flighting speed on the following PTO-SD augers, the 14 and 25 tooth sprockets must be replaced: Note: • PTO-SD 8" diameter - all lengths up to and including 51’. Replacement sprockets are included in the PTO-SD shipping carton.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL Important: Important: 30641 R1 3. ASSEMBLY 3.12. TRUSS 4. Pull truss cable over truss support brackets, around upper truss anchor and back over truss support brackets to lower truss anchor, holding it loosely in place with one 5/16” cable clamp at upper truss anchor, and two 5/16” cable clamps at each truss support bracket. Do not tighten cable clamps at this time. 5.
3. ASSEMBLY 3.12. TRUSS WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL Figure 3.12 Figure 3.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 3. ASSEMBLY 3.12. TRUSS Figure 3.14 Important: 30641 R1 9. For 71’ augers only (Figure 3.14). a. Fasten short truss anchor (A) to lower auger tube with 7/16” x 1" bolts and locknuts. b. Fasten high truss support bracket to mount (C) on bottom of center tube with 7/16” x 1" bolts and locknuts. c. Attach eyebolt to one end of truss cable with two 5/16” cable clamps, then insert eyebolt into short truss anchor and thread on nut a short way. d.
3. ASSEMBLY 3.13. TRANSPORT UNDERCARRIAGE WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 3.13. TRANSPORT UNDERCARRIAGE 1. To assemble undercarriage, fasten the lower reach arms to axle with three 7/16” x 1" bolts and locknuts on each side. • The 10" x 51' auger and all 56’, 61’ and 71’ augers require 1/2” x 1-1/4” bolts and locknuts. 2. Attach long crossmember to bottom of undercarriage brackets as shown in Figure 3.15, with two 7/16” x 1" bolts and locknuts.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL Note: 3. ASSEMBLY 3.13. TRANSPORT UNDERCARRIAGE Installing tires may not leave you with enough clearance to position and attach undercarriage once auger tube is raised. If so, install wheels after assembly is complete. g. Check that pressure of pre-inflated tires matches pressure indicated on tire sidewall. Mount wheels on hubs and attach with six 1/2” x 1-3/4” wheel bolts. 6.
3. ASSEMBLY 3.13. TRANSPORT UNDERCARRIAGE WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 9. Add the Stabilizer Kit as part of above Step 9 to the following augers: 8" x 56’-61’-71' 10" x 51’-61’-71' Figure 3.17 a. Attach short crossmember to small frame brackets loosely with two 1/2” x 1-1/2” bolts and locknuts, sandwiching the flat braces (B) between the short crossmember and small frame braces on each side (Figure 3.18). b.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL Important: 3. ASSEMBLY 3.14. WINCH & LIFTCABLE Where applicable, make sure that the lower reach arms are attached to the proper reach arm bracket (Figure 3.12 and 3.13). 10. Attach upper lift arms to roller track shoe with one 5/8” x 6-1/2” bolt and locknut. Do not overtighten. Tighten snug only; this bolt acts as a pivot point (Figure 3.21). • The 8" x 56’-61’-71' and the 10" x 51’-61’-71' augers require a 3/4” x 6-1/2” bolt and locknut.
3. ASSEMBLY 3.14. WINCH & LIFTCABLE WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL Important: Winch handle must be positioned on the left side of the auger (determine left by standing at the intake end, facing the discharge end). Important: 2. Attach winch to winch mount with three 3/8” washer locknuts. Winch handle must be positioned on the left side of the auger (determine left by standing at the intake end, facing the discharge end).
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 3. ASSEMBLY 3.15. TRANSPORT SADDLE MODEL K1051 & K1550 See Figure 3.26. 1. Slide handle over flat sides of input shaft. 2. Fasten with 1/2” locknut. Important: Do not remove or loosen the double locknut on the input shaft: it is an important part of the brake system of the winch. Figure 3.26 MODEL K2550 See Figure 3.27. 1. Slide handle over flat sides of input shaft. 2. Fasten with 1/2” locknut.
3. ASSEMBLY 3.16. PLASTIC MANUAL HOLDER WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 3.16. PLASTIC MANUAL HOLDER Before beginning installation, ensure that all winch / auger lift controls are locked in place and shut down and/or lock out auger. 1. Attach holder to the lower frame arms. Manual holder must be accessible at all times, whether frame is up or down. 2. The manual holder cap must face up (towards the intake end). Attach manual holder with supplied zip ties.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 3. ASSEMBLY 3.17. MODEL DECAL PLACEMENT 3.17. MODEL DECAL PLACEMENT Figure 3.29 Important: Do not cover any existing safety or instruction decals with the model decals. For most decal placement, follow the figure above. Apply decals to both sides of auger tube. Lower Tubes: Place decals just below the angle flange, centered on the tube. Decals must be easily seen from the ground when auger assembly is complete.
3. ASSEMBLY 3.17.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 4. TRANSPORT & PLACEMENT 4.1. TRANSPORT PROCEDURE 4. Transport & Placement WARNING Before continuing, ensure you have read and understand the relevant information in the safety section. Safety information is provided to help prevent serious injury, death, or property damage. 4.1. TRANSPORT PROCEDURE Follow all safety precautions when transporting the auger and use a proper towing vehicle. Important: 1.
4. TRANSPORT & PLACEMENT 4.2. PLACEMENT PROCEDURE WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 4. Beware of overhead obstructions and electrical wires and devices. The PTOSD augers have minimum clearances from 9' (2.74 m) to 15'6" (4.72 m) in normal transport position. 5. Refer to “Transport & Placement Safety” on page 11 for important safety information before towing. 4.2. PLACEMENT PROCEDURE Important: 1. Ensure towing hitch is in place and secure. Use a type of hitch pin (see Figure 4.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL Important: 4. TRANSPORT & PLACEMENT 4.2. PLACEMENT PROCEDURE 6. Once auger is in position, chock wheels on both sides and apply the park brake on the tractor (or chock its wheels as well) to prevent movement during operation. When releasing auger from the towing vehicle, test the intake end for downward weight. Do not raise the intake end above drawbar height.
4. TRANSPORT & PLACEMENT 4.2.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 5. OPERATION 5.1. PRE-OPERATIONAL CHECKLIST 5. Operation WARNING Before continuing, ensure you have read and understand the relevant information in the safety section. Safety information is provided to help prevent serious injury, death, or property damage. 5.1. PRE-OPERATIONAL CHECKLIST Before operating auger each time, the operator must confirm the following: • • • • • • • • All fasteners are secure as per assembly instructions.
5. OPERATION 5.3. OPERATION PROCEDURE WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 5.3. OPERATION PROCEDURE 5.3.1. START-UP & BREAK-IN Important: 1. Properly place auger and complete the pre-operational checklist at the beginning of this chapter. If everything is satisfactory, prepare for a 30-minute operation at half speed. 2. Correctly position portable grain hopper secure it to the auger with both straps (where applicable). Anchoring and/or support auger during operation.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 5. OPERATION 5.3. OPERATION PROCEDURE USE OF GRAIN SPREADERS: Many grain spreaders cannot handle the large capacity of some augers. Some augers plug, causing damage to the flighting and other drive components. This type of damage is not covered by warranty. Hints on how to avoid this... • • • • • • Get a larger spreader, if available. Remove the spreader. Make sure spreader is turned on. Center auger spout on spreader.
5. OPERATION 5.3. OPERATION PROCEDURE WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL • If the problem is plugging, clear as much of the grain as possible using a piece of wood, wet/dry vac, or other tool before restarting auger. Do not reach in and use your hands even if the tractor has been locked out. 2. If auger tube is full of grain, do not restart at full speed. Engage PTO at low rpm, gradually increasing power until normal operating speed is reached.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 6. MAINTENANCE & STORAGE 6.1. GENERAL MAINTENANCE PROCEDURES 6. Maintenance & Storage WARNING Before continuing, ensure you have read and understand the relevant information in the safety section. Safety information is provided to help prevent serious injury, death, or property damage. Proper maintenance habits on the PTO-SD auger mean a longer life, better efficiency, and safer operation. 6.1.
6. MAINTENANCE & STORAGE 6.2. GENERAL STORAGE PROCEDURES WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL Area Maintenance Procedure Note: Service winch with auger in fully lowered position and cable slack. Keep a film of grease on gears. Oil the ratchet pawl pivot, bushings, and pinion threads. Do not get oil or grease on brake discs. Replace brake discs if less than 1/16” (1.6 mm) thick. Check for proper ratchet pawl operation.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL Note: 30641 R1 6. MAINTENANCE & STORAGE 6.2. GENERAL STORAGE PROCEDURES Use only genuine Wheatheart replacement parts or equivalent. Replacement parts such as intake guards, pulley guards, PTO driveline shields, winches and lift cables Must meet ASAE standards or serious injury may result. Use of unauthorized parts will void warranty. If in doubt, contact Wheatheart or your Wheatheart dealer. Do not modify any auger components.
6. MAINTENANCE & STORAGE 6.2.
WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL 7. TROUBLESHOOTING 7. Troubleshooting . Problem Excessive noise or vibration. *Remember to follow proper break-in procedures—auger may run rough until tube is polished. If noise is extreme from outset or continuous after several loads of grade are fed, continue with troubleshooting below Possible Cause Chatter from wooden bearings. Truss cables incorrectly adjusted. Flighting peeled back due to plugging. Top drive inadequately lubricated.
7. TROUBLESHOOTING Problem Premature wear on auger tubes. 54 WHEATHEART - GHR & WHR GRAIN AUGERS PTO-SD DRIVE MODEL Possible Cause Remedy Auger being run at low capacity or empty for extended period of time. Bent flighting. Frequently occurs on farms using grain wagons. Auger should not be left unattended when filling bins. Depending on application, a belt conveyor may be more appropriate. Flighting allowed to wear beyond normal point of replacement.
LIMITED WARRANTY Wheatheart warrants to the buyer that the new machinery is free from defects in material and workmanship. This warranty is only effective for any new machinery that has not been altered, changed, repaired, or treated since its delivery to the buyer, other than by Wheatheart or its authorized dealers or employees, and does not apply to accessories, attachments, tools, or parts sold or operated with the new machinery if they have not been manufactured by Wheatheart.
Part of the Ag Growth International Inc. Group P.O. Box 39 Rosenort, Manitoba, Canada R0G 1W0 Phone: (866) 467-7207 (Canada & USA) Fax: (866) 768-4852 website: www.wheatheart.com email: sales@wheatheart.