LOT NUMBER: DATE PURCHASED: / / Millstead 60in Fireplace Console Model # WSF60MS26GAO # WSF60MS26WW ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our toll-free customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: 1-866-942-5362 Pacific Standard Time: 8:30 a.m. - 4:30 p.m.
IMPORTANT Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-abrasive surface. You will need the parts identified on page 3 and 4 of this instruction manuals. NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH THE DOWELS. EXCESS GLUE CAN BE WIPED OFF WITH A DAMP CLOTH. Insert dowel at least half way by tapping lightly with a rubber mallet (not included), IF NECESSARY.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Top Panel (Qty. 1) B- Fixed Shelf (Qty. 1) D- Left Side Panel (Qty. 1) E- Right Side Panel (Qty. 1) F- Left Partition Panel (Qty. 1) H- Middle Crossbar (Qty. 1) I- Middle Left Stile (Qty. 1) K- Base Front Molding (Qty. 1) L- Base Front Stretcher (Qty. 1) G- Right Partition Panel (Qty. 1) J- Middle Right Stile (Qty.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. V- Wood Door Insert (Qty. 2) Fireplace Insert (Qty. 1) Remote Control with Battery (Qty. 1) (Pre-attached) (1) Cam Lock (Qty. 32+1 extra) (2) Cam Bolt (Qty. 32+1 extra) (3) M8 x 30 mm Wood Dowel (Qty. 37+1 extra) (4) M3.5 x 12 mm Screw (5) M3.5 x 15 mm Washer Head Screw (6) M4 x 38 mm Screw (7) M3.5 x 15 mm Pan Head Screw (Qty. 20+1 extra) (Qty.
Assembly Instructions C 2 B F G 1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a carpeted floor or the empty carton to avoid any scratch. 2. Securely screw the Cam Bolts (2) into the designated small holes on the Fixed Shelf (B), Bottom Panel (C) and Partition Panels (F and G) with a Phillips screwdriver. NOTE: Screw-in cam bolts must be screwed down flush. 3 H 3 3 3 I 3 3 J 3.
Assembly Instructions 1 H 1 1 B 4. Align and attach the Middle Crossbar (H) to the Fixed Shelf (B) by engaging three Cam Locks (1) (Refer to page 2 on Cam Lock system operation supplement). I 1 1 F 5. Align and attach the Middle Left Stile (I) to the Left Partition Panel (F) by engaging two Cam Locks (1).
Assembly Instructions J 1 1 G 6. Align and attach the Middle Right Stile (J) to the Right Partition Panel (G) by engaging two Cam Locks (1). 3 3 3 3 3 3 C 3 3 3 L M 3 3 3 3 3 3 F 3 3 3 3 G B 3 3 3 3 7. Glue the Wood Dowels (3) into the inner holes of Fixed Shelf (B), Bottom Panel (C), Partition Panels (F and G), Base Front Stretcher (L) and Base Rear Stretcher (M) as shown. NOTE: Do Not insert the wood dowels into the cam bolts holes.
Assembly Instructions G B B F/G 1 F 8. Attach the Fixed Shelf (B) beween the Partition Panels (F and G) by engaging four Cam Locks (1). 1 C L C 9. Align and attach the Base Front Stretcher (L) to the Bottom Panel (C) with four Cam Locks (1).
Assembly Instructions 1 C M C 10. Align and attach the Base Rear Stretcher (M) to the Bottom Panel (C) with three Cam Locks (1). G B F L 8 C 8 8 8 11. Using the wood dowels as a guide, firmly press the assembled Partition Panels (F and G) to the Bottom Panel (C) and fasten them in place with four 50 mm Screws (8). Fully tighten the screws with a Phillips screwdriver.
Assembly Instructions 2 A E D 12. Securely screw the Cam Bolts (2) into the designated small holes on the Top Panel (A) and Side Panels (D and E) with a Phillips screwdriver. 3 3 3 K E 3 3 3 D 3 3 13. Glue the Wood Dowels (3) into the inner holes on both Side Panels (D and E) and the Base Front Molding (K) as shown.
Assembly Instructions E G B D/E C F 1 C D 14. Align the large holes on the Left Side Panel (D) with the inserted Wood Dowels (3) on the assembled base. Firmly press them together and fasten it in place by engaging three Cam Locks (1). 15. Repeat the same procedure to attach Right Side Panel (E) at the other end. 6 E B 6 C D 16. Fasten the Base Front Stretcher (L) to both Side Panels (D and E) with four 38 mm Screws (6).
Assembly Instructions K E 6 B 6 C 6 D 6 17. Attach the Base Front Molding (K) to the Base Front Stretcher (L) by using eight 38 mm Screws (6). 1 A E B C D 18. Place the Top Panel (A) onto the inserted Wood Dowels (3) properly and fasten it in place by engaging eight Cam Locks (1).
Assembly Instructions 4 9 D A B I H C E 19. Ask for assistance to flip the unit around at its front edge as shown. 20. With the pilot holes as a guide, fasten the Middle Crossbar (H) to the Middle Stiles (I and J) by attaching two Mending Plates (9) at the joints, using two 12 mm Screws (4) per plate. 5 R Q S C E 21. Now, go back and securely tighten all the cam locks and screws. Make sure that all the parts are tight and there are no gaps between the parts. This will help keep the unit square. 22.
Assembly Instructions A E D N N 13 4 N N N 24. Ask for assistance to lift the assembly unit upright and position it near the final location. 25. Insert eight Shelf Supports (13) into the holes at the desired height inside each side compartment. Make sure you place four shelf supports in the same level, so the shelf is not tilted. Tilt and rest the Adjustable Shelves (N) onto the Shelf Supports (13) and secure them into place with 12 mm Flat Head Screws (4). A 1 E P D 2 P 26.
Assembly Instructions A P E 12 11 12 D P 12 11 12 29. Open the doors and attach one Handle (11) to the front side of each Door (P) with two 22 mm Bolts (12). P V T Wood Panel Glass Panel U Mesh Trim NOTE: The doors are shipped with Wood Door Insert Panels (V). You can keep the doors as they are or interchange with the Door Glass Insert (T) or Mesh Trims (U) depending on your configuration. 30.
Assembly Instructions A 15 D 16 16 31. Plug Cam Lock Covers (15) onto the visible Cams Locks to conceal the cams. 32. Stick the Rubber Bumpers (16) on the outer corners of the Doors (P) where they meet the partition panels. 7 O 10 A E A O F/G E C O 7 33. Lift the fireplace insert carefully into the back of the assembled mantel and center it in the opening. DO NOT drag the insert across the Bottom Panel (C) as it may scratch the unit. 34.
Assembly Instructions A D NOTE: To prevent your TV from tipping, you must install the acrylic TV stopper if you place a flat panel television on the top panel. Otherwise, skip to step 37. 36. Remove the paper backing from the Acrylic Stopper (14), then properly align the acrylic stopper into the cut-out on the acrylic stopper template on the Top Panel (A). Press down on the acrylic stopper to help adhesion. 37.
Assembly Instructions Tools required (not provided): Phillips screwdriver, stud finder, tape measure, pencil, power drill and 1/8’’ drill bit. 38. Ask for assistance to position the assemble fireplace at the desired location against a wall. If necessary, adjust the pre-attached Floor Levelers at the bottom of the Base Front Molding (K) to correct the tilting and level the doors. 39.
Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polishes is not necessary. Should you choose to use polishes, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage the finish. Never use water to clean your furniture as it may cause damage to the finish. Always use coasters under beverage glasses and flowerpots. Liquid spills should be removed immediately.
MAXIMUM RECOMMENDED WEIGHT LOADS MANUFACTURER: Whalen Furniture Manufacturing CATALOG : Millstead 60in Fireplace Console MODEL #: WSF60MS26GAO / WSF60MS26WW MADE IN VIETNAM FITS UP TO MOST 177.8 cm / 70 in. DIAGONAL FLAT PANEL TVS MAXIMUM LOAD 61.2 KG / 135 LB PLACE TV BEHIND THE STOPPER MAXIMUM LOAD 22.7 KG / 50 LB THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH FLAT PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND WEIGHT LIMITS.
