LOT NUMBER: DATE PURCHASED: / / Middleton 48" Fireplace Console Model # WSF48WV23-DB # WSF48WV23-WA OR ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our toll-free customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: 1-866-942-5362 Pacific Standard Time: 8:30 a.m. - 4:30 p.m.
MAXIMUM RECOMMENDED WEIGHT LOADS MANUFACTURER: Whalen Furniture Manufacturing CATALOG: Middleton 48" Fireplace Console MODEL # WSF48WV23-DB / WSF48WV23-WA MADE IN CHINA FITS UP TO MOST 152.4 cm / 60” FLAT PANEL TVs MAXIMUM LOAD 61.3 kg / 135 lb PLACE TV BEHIND THE STOPPER MAXIMUM LOAD 22.7 kg / 50 lb THIS UNIT IS NOT INTENDED FOR USE WITH CRT TVS. USE ONLY WITH FLAT PANEL TVS AND AUDIO/VIDEO EQUIPMENT MEETING RECOMMENDED SIZE AND WEIGHT LIMITS.
IMPORTANT Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and nonabrasive surface. You will need the parts identified on page 4 and 5 of this instruction manual. NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH THE DOWELS. EXCESS GLUE CAN BE WIPED OFF WITH A DAMP CLOTH. Insert Dowel at least half way by tapping lightly with a rubber mallet (not included), IF NECESSARY. 1 2 3 X 4 X CAM LOCK SYSTEM OPERATION HOW THE KNOCK DOWN (KD) ASSEMBLY SYSTEM WORKS 1.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Top Panel (Qty. 1) B- Base (Qty. 1) D- Upper Side Panel (Qty. 2) E- Upper Partition Panel (Qty. 1) G- Lower Left Partition Panel (Qty. 1) J- Adjustable Shelf (Qty. 2) M- Wood Door Panel (Pre-attached) (Qty. 2) N- Door Glass F- Lower Left Side Panel (Qty. 1) H- Lower Right Side Panel (Qty. 1) I- Lower Right Partition Panel (Qty.
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. (1) Cam Lock (Qty. 24+1 extra) (2) Cam Bolt (Qty. 24+1 extra) (4) M3.5 x 12 mm Flat Head Screw (Qty. 12+1 extra) (7) Metal Bracket (Qty. 2) (14) Flat Washer (Qty. 1) 4 mm Hex Wrench (Qty.1) (5) M3.5 x 15 mm Washer Head Screw (Qty. 38+1 extra) (8) Cam Lock Cover (Qty. 30+1 extra) (11) Handle Bolt (Qty. 4) (3) 8 mm x 30 mm Wood Dowel (Qty.
Assembly Instructions 2 A B C 1. Unpack the unit and confirm that you have all the hardware and required parts. Assemble the unit on a carpeted floor or the empty carton to avoid any scratch. 2. Securely screw the Cam Bolts (2) into the designated plastic bushings on the Top Panel (A), the Base (B) and the Center Shelf (C) using a Phillips screwdriver. UP 3 H 1 UP F B 3. Insert four Wood Dowels (3) into the bottom inner holes on Lower Side Panels (F and H).
Assembly Instructionsstile I 3 G 3 B 17 17 17 17 5. Glue four Wood Dowels (3) into the bottom inner holes on the Lower Partition Panels (G and I) and attach them to the Base (B) with four 50 mm Screws (17) using a Phillips screwdriver. 6 6 6 K 3 3 C 6. Glue two Wood Dowels (3) into the inner holes of the Middle Crossbar (K) and attach it to the Center Shelf (C) with three 63 mm Screws (6).
Assembly Instructions 3 C H I G F 7. Attach the previous assembly (C and K) to the Lower Side Panels (F and H) and Partition Panels (G and I) with eight Wood Dowels (3) and eight Cam Locks (1). 2 C 8. Ask for assistance to stand the unit upright. 9. Securely screw six Cam Bolts (2) into the plastic bushings on Center Shelf (C).
Assembly Instructions D E D C 10. Attach the Upper Side Panels (D) and Partition Panel (E) to the Center Shelf (C) with seven Wood Dowels (3) and six Cam Locks (1). A D E D 1 11. Attach Top Panel (A) to the Upper Side Panels (D) and Partition Panel (E) with seven Wood Dowels (3) and six Cam Locks (1).
Assembly Instructions 7 G K I 12. Ask for assistance to lay down the assembled unit at its front edges. Attach two Metal Brackets (7) at the joints where the Middle Crossbar (K) meets the Lower Partition Panels (I and G) with four 12 mm Flat Head Screws (4). A UP P O C 5 G UP 5 P D B H 13. Now, go back and securely tighten all the Cam Locks and the Screws. Make sure that all the parts are tight and there are no gaps between the parts. This will help keep the unit square. 14.
Assembly Instructions 9 H I G J F J J 9 4 8 16. Ask for assistance to stand the assembled unit upright. 17. Insert the Shelf Supports (9) into the desired holes in the sides of the side compartments. Make sure you place the four Shelf Supports (9) in the same level so the shelf is not tilted. Tilt and rest the Adjustable Shelves (J) onto the Shelf Supports (9) and secure the Adjustable Shelves (J) into place with 12 mm Flat Head Screws (4). 18.
Assembly Instructions M N L NOTE: The doors are shipped with Wood Door Panels (M). You can keep the doors as they are or interchange with the Door Glass Inserts (N) depending on your configuration. 20. To change the configuration, loosen the screws on the inside of Door Panels (L) and rotate the clips to remove the door insert panel. Replace with the desired panel, then rotate clips to secure the panel within the door frame and tighten screws. 1 H F L 2 L 21.
Assembly Instructions B 24. Lift the fireplace insert carefully into the back of the assembled mantel and center it in the opening. DO NOT drag the insert across the Base (B) as it may scratch the unit. The rubber bumper is against the firebox 3 5 Q 14 13 12 15 B 25. Using the pilot holes as a guide, align and attach two L-shaped Metal Braces (15) to the Base (B) by screwing one Washer Head Screw (5) in each. 26.
Assembly Instructions A NOTE: To prevent your TV from tipping, you must follow these instructions if you place a TV on top of your console. Otherwise, skip to “Step 28”. 27. Remove the paper backing from the Acrylic Stopper (16), then properly align the Acrylic Stopper into the cut-out on the acrylic stopper template on the Top Panel (A). Press down on the acrylic stopper to help adhesion. 28.
Assembly Instructions Tools required: Phillips screwdriver, stud finder, power drill and 1/8” drill bit. 29. Position the console at the desired location against a wall. If necessary, adjust the pre-attached floor levelers to correct tilting and/or level the doors. 30. Follow the instructions printed on the plastic bag containing the tipping restraint hardware to attach the tip-over restraints to the unit and the wall. NOTE: The tipping restraint hardware included is for wooden stud wall construction.
Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polishes is not necessary. Should you choose to use polishes, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage the finish. Never use water to clean your furniture as it may cause damage to the finish. Always use coasters under beverage glasses and flowerpots. Liquid spills should be removed immediately.
