Infrared Digital Scouting Camera User’s Manual Model # W3EA
Includes page 1 USB Cable 2 - Bungee Cords Camera Unit User Manual
Features RESOLUTION FLASH FLASH RANGE SENSOR SENSOR RANGE IMAGE FORMAT MEMORY USB IMAGE RESOLUTION POWER SUPPLY AUXILIARY POWER BATTERY LIFE ONBOARD POWER HOUSING MOUNTING MAX: 3 MP 20 High Intensity Infrared LED’s up to 40 feet Passive Infrared Sensor (PIR) Motion and Heat up to 60 feet JPEG - Digital Still / AVI - Digital Video up to 16GB SD Card (not included) 5-PIN Mini USB style - included High (3MP) Medium (1.3MP) Low (.
Installing Batteries 1. Open the door at the bottom of the camera by unlatching the locking tabs. Open Illustration A 2. page 3 With the camera facing open, open the battery compartment cover by sliding the latch to the left.
3. 4. Close battery compartment cover. To latch the cover simply pull the latch slightly to the left as you close the battery compartment cover. 5. Load SD memory card (up to 64GB not included) into the SD card slot with the connectors facing down. With the bottom of the camera towards you, Make sure to insert the batteries into the camera with the positive ends towards you where marked positive and the negative ends towards you where marked negative.
Power On 1. To turn the unit ON press and release the power button. Ready Clock Date Photos Image PIR Resolution Active Delay 2. Test Mode PM Still Hi Hi 24Hr 15s PM Still Hi Hi 24Hr 15s Lo Lo Night 1m 2. Image Capture Status Light: The LED status light illuminates Green when the camera has taken an image and is writing it to the SD card. 3. LCD Ready Mode: The camera will automatically enter the Ready Mode if a button is not depressed for greater than 30 seconds.
Power Save 1. 2. After 30 seconds without any buttons being pushed, the LCD will turn off and camera enters into Power Save or Ready Mode. Setting Time 1. To change date and time, start by pressing and release the center navigation button to set the hour. Ready Clock Date Photos Image PIR Resolution Active Delay The LCD screen can be awakened by pressing the Power button briefly.
Setting Date 1. Press the center navigation button after setting the minute to change the Day. Ready Clock Date Photos Image PIR Resolution Active Delay 2. page 7 MM DD Still Hi Hi 24Hr 15s MM DD Still Hi Hi 24Hr 15s 1. 1 0 29 Video Med Med Day 30s Lo Lo Night 1m 1 0 29 Video Med Med Day 30s Lo Lo Night 1m 2m When the DAY is set, repeat Open steps 1 and 2 to set the Month and Year. Press the center navigation button while PIR is selected. The highlighted option will be blinking.
Resolution 1. Press the center navigation button while Resolution is selected. The highlighted option will be blinking. Ready Clock Date Photos Image PIR Resolution Active Delay 2. PM Still Hi Hi 24Hr 15s 0432 Video Med Med Day 30s Lo Lo Night 1m RESOLUTION: HI: Images will be at the highest resolution but take up the most space. MED: Images will be at medium resolution and take up average space. LO: Images will be at the lowest resolution and take up the least space.
Active 1. Press the center navigation button while PIR Active is selected. The highlighted option will be blinking. Ready Clock Date Photos Image PIR Resolution Active Delay 2. Delay PM Still Hi Hi 24Hr 15s 0432 Video Med Med Day 30s Lo Lo Night 1m PM Still Hi Hi 24Hr 15s 0432 Video Med Med Day 30s Lo Lo Night 1m 2m PIR ACTIVE: 24 HR: The PIR can be active at all times. Open DAY: The PIR can be active in daylight hours only. NIGHT: The PIR can be active in nighttime hours only.
Power Off 1. Power Port To turn the unit off, first wake up the LCD screen and then depress and hold the power button until the LCD turns off. Ready Clock Date Photos Image PIR Resolution Active Delay PM Still Hi Hi 24Hr 15s 1. WGI Cameras come standard with an external power port. You must open the weather resistant cover and use a Wildgame Innovations 6 Volt camera battery accessory.
Mounting 1. When mounting to a tree, first latch the 2 bungee cords through the mounting holes on the left or right side of the camera. Then, stretch the cords around the tree and latch the other ends of the bungee cords through the mounting holes on the opposite side of the camera. Important Once you connect the camera to your computer via the USB cable/ports, the camera will then draw power from the computer.
Retrieving Images (SD Card in Camera) Method 1: Leave SD card in camera A. First, make sure that the camera is powered OFF. Next, plug the USB cable into the camera and then into the USB port on your computer. Once this is complete (in this order only), then power the camera ON. B. Once complete, your computer may automatically launch “AutoPlay”, a window recognizing a new Removable disk (the camera). C. If so, it should give you three selections: 1. Import pictures 2. View pictures 3.
Retrieving Images (SD Card reader) Method 2: Remove SD card and use card reader F. If your computer does not automatically launch the AutoPlay window recognizing A. First, remove the SD Card from the the Removable Disk (the SD Card), then you camera unit itself by pressing on it to will need to go to the “Start Menu” at the bottom left of your screen and select “Comwhere it automatically ejects. B. Next, insert the SD card into your SD puter”.
Warranty DISCLAIMERS WGI Innovations, LTD. is not responsible for damage, expense or injury caused by the unauthorized use of, alterations to, improper connection of and abuse or neglect of the WGI Innovations™ products. WARRANTY You must register your product warranty online at www.wildgameinnovations.com. Follow the on screen directions to complete the process. WGI Innovations, LTD.
FCC FCC STATEMENT Product Name: Game Trail Camera Trade Name: Wildgame Innovations Model# W3EA This device complies with Part 15 of the FCC Rules. Operation is subject to the following two criteria: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
page 16
602 Fountain Parkway Grand Prairie, TX 75050 800.847.8269 “Wildgame Innovations” and the “Button Logo” are TM trademarks of Wildgame Innovations, LLC. “Sport Responsible” , “Redux” and “Flextime” are TM trademarks of WGI Innovations, LTD.
