BASIC WORKBENCH, CONTINUOUS BENCH WITH COMMON LEG AND ACCESSORIES INSTALLATION INSTRUCTIONS IMPORTANT: To reduce the risk of serious injury, read and understand this entire guide before beginning any installation.
Contents BEFORE YOU BEGIN: .................................................................................................................................................... 3 SAFETY WARNINGS: ..................................................................................................................................................... 3 Basic Workbench .....................................................................................................................................................
BEFORE YOU BEGIN: 1. Check your inventory to be sure you received your entire order. If there are any missing or damaged parts, contact your Dealer or Customer Service Manager. NOTES: Each workbench is packaged separately. Each unit features an identification sheet located on the face of the unit. The identification sheet will match the items detailed in contents above. 2. Read and understand the entire installation instructions prior to beginning the install.
Basic Workbench Do not tip bench on its side, without a shelf attached as it is unstable and may cause damage. Must use two people to rotate bench. STEPS Lay bench top face down on a flat clean surface; such as blanket or cardboard to protect from scratching. Insert leg attachment channel into bench top with open area of channel facing upward. Position attachment channel so that holes in end flanges are in line with oval and first hole in front and back flanges of benchtop.
Workbench with All-Wood Top Do not tip bench on its side, without a shelf attached as it is unstable and may cause damage. Must use two people to rotate bench. STEPS Leg Attach stringer to leg weldment. Position stringer so that holes in end of stringer are in line with holes in legs; locate approximately 11-5/8” down from top of leg weldment. Fasten stringer to leg with four (4) 07792-00 screws and 100530-00 weldnuts provided. Repeat step for opposite end.
Continuous Bench with Common Leg Benches over six (6) feet long may be obtained by placing end to end, a starter unit and an add-on unit. Each addon unit contains one (1) bench top, one (1) stringer, one (1) leg attachment channel, one (1) leg weldment and two (2) adjustable feet, and associated hardware. STEPS Lay bench top face down on a flat clean surface; (such as blanket or cardboard to protect from scratching). Placing them end to end to completed steps 1-3 for both benches.
Shelf for Basic Workbench STEPS Place shelf on shelf supports between legs of workbench with back edge of shelf (edge with 90° flange is back) approximately .062 (1/16”) from back legs of workbench. Position shelf so two inner holes on each end of shelf are in line with two (2) inner holes of each shelf support. Fasten shelf to shelf supports with four (4) 07792-00 and 17213-00. This completes assembly of shelf assembly for basic workbench.
Footrest for Basic Work Bench STEPS Place footrest on shelf supports between legs of work bench with open area of footrest channel facing downward. Position footrest so that the inner holes, in each end of footrest, are in line with inner holes in each shelf support (NOTE: Footrest can be positioned at any one of four (4) locations in the shelf supports). Fasten footrest to shelf supports with two (2) screws, washers, and nuts as provided, one (1) each end.
End Guards STEPS Position end guard so that two (2) holes align with holes in side of attachment channel. Fasten end guard to channel with two (2) 07792-00 and 17213-00. Repeat procedure at the other end. This completes end guard assembly. Back Guard STEPS Position back guard so that ovals in lower edge of back guard are in line with holes in back edge of bench top. (Flanges on back guard are to be facing toward front). Fasten back guard to bench top with five (5) 07792-00 and 17213-00.
Back & End Filler Panels STEPS Place end of ledge shelf in between flanges of ledge end. The two (2) holes on back of shelf must align with top two (2) ovals on rear flange of ledge end. Align hole in front flange of ledge shelf with top hole on front flange of ledge end. Fasten ledge shelf to ledge end with three (3) screws and nuts as provided. Repeat procedure at the other end.
Ledge Riser for Work Bench with End Guards and Back Guard STEPS Place ledge assembly on bench top flush against end guards and/or back guard. The bottom oval in the sides of ledge ends must align with hole in back corner of end guards and/or hole in end flanges of back guard. Fasten ledge assembly to end guards and/or back guard with one (1) screw and nut as provided. If both end guards and a back guard are on work bench, remove hardware holding two (2) pieces together at each rear corner.
Once installation is completed, a copy of the installation instruction booklet MUST remain with the customer. WARRANTY We extend to the original purchaser from the date of purchase a limited lifetime warranty for our Automotive Workstations and Modular Drawer Cabinets against manufacturing defects in material and workmanship. For all other products we extend to the original purchaser from the date of purchase a 5-year limited warranty against manufacturing defects in material and workmanship.
