INFRARED PANEL HEATER INSTRUCTIONS MANUAL Congratulations on purchasing WEXSTAR Infrared Heater. WEXSTAR focuses on reaching the highest quality standards and optimal heating performance with the lowest possible energy consumption. With the WEXSTAR infrared heater you will witness the heat being distributed uniformly in the room and absorbed by objects and walls that release the warmth back into the room. This creates an overall cozy and comfortable feeling of heat. By: Spacio Innovations Inc.
SYMBOLS Warning This signal word indicates a hazard with an average risk level which, if not avoided, can result in serious injury or death. Warning of electrical voltage This symbol indicates dangers to the life and health of persons due to electrical voltage. Symbols Meaning This symbol located on the device indicates that it is prohibited to place objects (such as towels, clothes etc.) above or directly in front of the device. To avoid overheating and fire hazards, the device must not be covered.
CONTENT 1┃WARNINGS & PRECAUTIONS 2┃FEATURES 3┃TECHNICAL INFORMATION 4┃SCOPE OF SUPPLY 5┃DEVICE STRUCTURE 6┃INSTALLATION 7┃TROUBLESHOOTING 8┃MAINTENANCE & SERVICING 9┃STORAGE 10┃WARRANTY 11┃DISPOSAL 12┃ACCESSORIES SOLD SEPARATELY -3-
1┃WARNINGS & PRECAUTIONS Read this manual carefully before starting or using the device. Always store the manual in the immediate vicinity of the device or its site of use! In this manual there is important information for the installation of your infrared heater. You have acquired an ecologic, economic heater and are thereby making an effective contribution towards saving the environment. This heater can be used with a thermostat.
8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Warning Children of less than 3 years should be kept away unless continuously supervised.
• Remove all the protective films (both on the front and on the back) before using. • Be sure the input voltage is between 120V, 60Hz. • Do not use the device in potentially explosive rooms. • Set the device up in an upright and stable position. • Let the device dry out after a wet clean. Do not operate it when wet. • Do not use the device with wet or damp hands. • Do not expose the device directly to squirting water. • Never insert any objects or limbs into the device.
• Insert the mains plug into a properly secured mains socket. • Do not use the device when the socket or wire is overloaded. • Observe the device's power input, cable length and intended use when selecting extensions to the power cable. Completely unroll extension cables. Avoid electrical overload. • Before carrying out maintenance, care or repair work on the device, remove the mains plug from the mains socket.
• Do not use this device near bathtubs, shower trays, swimming pools or other water containers that can cause a risk of electric shock! • The device must be placed where the switches and controllers cannot be touched by a person in a bathtub or shower. IMPORTANT INSTRUCTIONS WHEN THE HEATER IS USED AS A MOVABLE HEATER WITH THE STAND SUPPORT • Read all instructions before using this heater as a movable heater. • This heater is hot when in use. To avoid burns, do not let bare skin touch hot surfaces.
locate heater where it may fall into a bathtub or other water container. • Do not run the cord under carpeting. Do not cover the cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over. • To disconnect the heater, turn controls to off, then remove plug from outlet. • Connect to properly grounded outlets only. • A heater has hot and arcing or sparking parts inside.
2┃FEATURES • The device is designed to provide an efficient, comfortable and healthy heating system for any domestic users. • These devices do not require air circulation to transmit the heat and help to maintain a clean, silent, dust free environment. • A wide range of devices available in a huge choice of sizes and styles.
Rated Curre nt Mounting way 350W 2.92A Wall only 705*605*25 450W 3.75A Wall only F-580WA 1005*605*25 580W 4.83A Wall only F-700WA 1195*595*25 700W 5.83A Wall only F-900WA 1205*755*25 900W 7.50A Wall only F-1100W A F-270CE 1205*905*25 1100W 9.17A Wall only 595*595*25 270W 2.25A Ceiling only F-320CE 705*605*25 320W 2.67A Ceiling only F-450CE 1005*605*25 450W 3.75A Ceiling only F-550CE 1195*595*25 550W 4.58A Ceiling only F-700CE 1205*755*25 700W 5.
4┃SCOPE OF SUPPLY • 1 x Heating device • 4 x Screws • 4 x Anchors • 1 x Manual • 1 x Drilling template These kits can be used for wall mounting only, special kits shall be used for ceiling mounting, please consult the supplier before installation.
6┃INSTALLATION Make sure remove all the protective films (both on the front and back)! Instruction for Wall Mounting IMPORTANT: this way is for wall mounting only! 1. Choose the mounting position, keep the required minimum distances. Distances required for device mounting front Minimum 30cm / 12” left Minimum 10cm / 4” right Minimum 10cm / 4” top Minimum 50cm /20” 2. Mark the positions for the bore holes onto the drilling template (D) if there are no existing marks.
3. Insert the screws into the anchors and fasten the screws. The screws should protrude approx. 0.5 cm / 0.2” from the dowels. 4. Hang the infrared heating device (A) in. 5. Slid the device to make the screws into the correct positions as showing in below drawing. 6. Plug in to start using the heating device. Do pull out the plug when not in use.
Instruction for Ceiling Mounting Way A: The below ceiling mounting set is included with the ceiling mounting heaters models only. X 2 SETS 1. Drill two holes on the ceiling with correct distance A and distance B.
2. Mount the two hanging units onto ceiling with screws, and turn the screws to the end tightly, this is very important. 3. Take off all the four plastic caps from the rear of the panel. 4. Slide the panel to make ceiling hanging units into one side of the panel rear bracket first, then push the whole panel close to ceiling and slide the panel back, to make the other end of the ceiling hanging unit enters the other side.
(View after mounting finished) Instruction for Ceiling Mounting Way B: The below ceiling mounting set is not included, and it is sold as a separate accessory.
1.Drill four 2mm diameter holes on the rear of the panel if there are no such small holes exists. Insert short screws G into B and screw them into the holes. 2. Tighten wires I to B by screwing C.
3. Drill four 6mm holes on the ceiling and fix the plastic expansion tubes H on the ceiling. 4.Insert the long screws F into the expansion tubes H through the top lock metal head E, then tighten up the screws into the tubes.
5.screw D which is at the other end of the wire into E tight. 6.Press the automatic locking extractor to adjust the desired length of the steel wire. Release the locking extractor, then it will lock the wire automatically.
7┃TROUBLESHOOTING Problem It has noise when original charged with electricity Reason Due to the structure stress of the heat insulator. Measure It is a normal phenomenon. Don't worry about it. The surface of the device was slightly raised. Due to the thermal expansion of the surface material. It is a normal phenomenon. Don't worry about it. The surface of the heating device is slightly warm. 1. The voltage is low. 2. In a low-temperature environment. 1. Install a voltage regulator. 2. It is normal.
Cleaning the device Warning of electrical voltage Never immerse the device in water! Clean the device with a soft, damp and lint-free cloth. Ensure that no moisture enters the heater housing. Protect electrical components from moisture. Do not use any aggressive cleaning agents such as cleaning sprays, solvents, alcohol-based or abrasive cleaners to dampen the cloth.
10┃WARRANTY WEXSTAR Electric Panel Heaters are warranted against defects in workmanship and materials for three (3) years from date of purchase.
11┃DISPOSAL The icon with the crossed-out waste bin on waste electrical or electronic equipment stipulates that this equipment must not be disposed of with the household waste at the end of its life. You will find collection points for return of waste electrical and electronic equipment in your vicinity. The addresses can be obtained from your municipality or local administration.
12┃ACCESSORIES SOLD SEPARATELY WEXSTAR Thermostat with Remote Control.
WEXSTAR Plug-in Thermostat for Infrared Panel Heater Model: TH-926T Pair of Stand Feet for F Type Panel Heaters.
Model F-CEKIT1 Model F-CEKIT3 Contact Us: Spacio Innovations Inc. Email: info@spacioinnovations.com www.spacioinnovations.com If any items are missing or damaged when opening the box: PLEASE CONTACT US BEFORE RETURING THE HEATER TO THE RETAIL STORE! Please direct all inquiries to: info@spacioinnovations.
