Assembly Instructions Note: Please help to read my instruction before you ready to assemble.
Part List Label Picture Description QTY (PCS) A Backrest 1 B Left Armrest 1 C Right Armrest 1 D Seat 1 E Front Rail 1 F Seat Cushion 3 G Leg 4 Page 2 OF 9
Hardware ① Plastic Washer 7 ② Allen Wrench 1 Assembly Preparation All Including: x3 x4 x1 x7 Included: -Backrest 1pc -Left Armrest 1pc -Right Armrest 1pc -Seat 1pc -Front Rail 1pc -Seat Cushion 3pcs -Leg 4pcs -Allen Wrench 1pc -Plastic Washer 7pcs NOTICE: -Please read the instruction from cover to cover in detail.Thanks. -Installed by at least two adults -To avoid damaging your furniture ，Please don't assemble on flooring or carpet.
Assembly Steps OVERVIEW Backrest(A) Left Armrest(B) Seat Cushion(F) Right Armrest(C) Front Rail(E) Leg(G) This Sofa has multiple parts and may require up to 60 minutes to assemble. To give you an overview of the Sofa parts, the above picture is to help you put the various parts into perspective. Please read through the instructions below to familiarise yourself with the parts and steps before assembly. Note: It is recommended that you have an adult partner to assist during the entire assembly process.
Step 2 Right Armrest(C) Front Rail(E) Left Armrest(B) With the assistance of your partner,slide the hook in the eng of Front Rail(E) into the bolts on the Left Armrest(B) and Right Armrest(C), as shown in Picture. Step 3 Backrest(A) Loosen the 2 bolts in Backrest(A) around half inch by Allen Wrench( ②).
Step 4 Right Armrest(C) Backrest(A) Left Armrest(B) Keep the Backrest(A) and the back of the Left Armrest(B), Right Armrest(C) flat. Slide the Tapered Connectors on the Backrest(A) into the Tapered Connectors on the Left Armrest(B) as shown in the picture. Repeat the same process with the Right Armrest(C). Note: Make sure the Tapered Connectors on Backrest(A) lock into the Tapered Connectors on the Left Armrest(B) and Right Armrest(C).
Step 5 Seat(D ) Front Rail(E ) With the assistance of your partner,lift the rope on the two sides of Seat(D) by hand. Put the Seat(D) on the wood bar of the Front Rail(E) and then slowly place it down as shown above. Note:All the u-shaped iron sheet need clamped to the bolt. Step 6 Left Armrest(B) Right Armrest(C) Backrest(A) Tilt and lay the Sofa onto a flat surface. Tighten the Bolts in the bottom of Backrest(A),Left Armrest(B) and Right Armrest(C) by Allen Wrench( ②) as pictured above.
Step 7 Right Armrest(C) Left Armrest(B) Front Rail(E) Change tilt and lay the Sofa another side onto a flat surface. Tighten all the Bolts at the end of bottom Left Armrest(B) and Right Armrest(C) by Allen Wrench( ②) as pictured above. Tighten the Bolts fully in a sequential manner. Step 8 Left Armrest(B) Right Armrest(C) Leg(G) Install the Leg(G) at the bottom of Left Armrest (B) and Right Armrest(C) by placing Plastic Washer( ①) on the threaded stem.
Step 9 Seat Cushion(F) Turn the Sofa to its upright position. Place the Seat Cushions(F) onto the Sofa. Step 10 Your Sofa is ready for use. This sofa can only be used on a flat, level surface.
