Instruction manual

ManualsBrandsWeston ManualsKitchen Appliances08-3201-W

SAVE THESE INSTRUCTIONS!

REFER TO THEM OFTEN AND USE THEM TO INSTRUCT OTHERS.

NEVER operate Grinder

without the Tray

secured in place.

To avoid serious or fatal injury,

NEVER reach into any

Grinder inlet.

ALWAYS use the Stomper to

push meat into the Grinder Head.

Read & fully understand

all instructions

& warnings prior to use.

WARNING!

NEVER operate Grinder without the

Tray secured in place.

To avoid serious or fatal injury, NEVER reach

into any Grinder inlet.

ALWAYS use the Stomper to push meat

into the Grinder Head.

Read & fully understand all instructions

& warnings prior to use.

WARNING!

ATTENTION

If any components of this unit are broken,

do not operate properly, or for product returns,

please contact Pragotrade LLC at

1-800-814-4895

Outside the U.S. call 440-638-3131.

For the online catalog, log onto www.westonsupply.com.

Exclusively imported by Pragotrade LLC Strongsville, Ohio

www.pragotrade.com

LLC

u.s.a.

Summary of content (12 pages)

PAGE 1
u.s.a. LLC ATTENTION If any components of this unit are broken, do not operate properly, or for product returns, please contact Pragotrade LLC at 1-800-814-4895 Outside the U.S. call 440-638-3131. For the online catalog, log onto www.westonsupply.com. Exclusively imported by Pragotrade LLC Strongsville, Ohio www.pragotrade.com SAVE THESE INSTRUCTIONS! REFER TO THEM OFTEN AND USE THEM TO INSTRUCT OTHERS. WARNING! NEVER operate Grinder without the Tray secured in place.
PAGE 2
WARNING! IMPORTANT SAFEGUARDS When using electrical appliances, basic safety precautions should always be followed including the following: 1. READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE. 2. To protect against risk of electrical shock, do not submerge or use this appliance near water or other liquid. 3. Unplug this appliance from the electrical outlet when not in use or before putting on or taking off parts and before cleaning. 4.
PAGE 3
REV021810 RECIPES COMMERCIAL GRADE ELECTRIC MEAT GRINDER VENISON SAUSAGE 6 lb venison ½ tsp cayenne pepper 2 tsp pepper . . . .
PAGE 4
COMPONENT LIST DIAGRAM NUMBER PART DESCRIPTION #08 08-0801-W #12 08-1201-W #22 08-2201-W #32 08-3201-W 1 Front Ring Nut 08-0842 08-1242 08-2242 08-3242 2 4.
PAGE 5
NOTE: Special considerations must be made when using venison or other wild game, since it can become heavily contaminated during field dressing. Venison is often held at temperatures that could potentially allow bacteria to grow, such as when it is being transported. Refer to the USDA Meat and Poultry Department for further questions or information on meat and food safety.
PAGE 6
IMPORTANT SAFETY RULES WARNING! READ AND FULLY UNDERSTAND ALL INSTRUCTIONS AND WARNINGS PRIOR TO USING THIS UNIT. YOUR SAFETY IS MOST IMPORTANT! FAILURE TO COMPLY WITH PROCEDURES AND SAFEGUARDS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE. REMEMBER: YOUR PERSONAL SAFETY IS YOUR RESPONSIBILITY! 1. DO NOT use the Grinder without the Tray secured into place. 2. ALWAYS DISCONNECT Grinder from power source before servicing, changing accessories or cleaning the unit. 10. NEVER LEAVE THE GRINDER UNATTENDED.
PAGE 7
CIRCUIT BREAKER INSTRUCTIONS FIGURE 16 This Grinder is equipped with a Circuit Breaker as a safety precaution. If the Grinder should stop running follow these steps to remedy: 1. Turn the Grinder to the “Off” position. 2. Press the Circuit Breaker Reset Button O I (Figure 16). 3. Turn the Grinder back on and resume grinding. Circuit Breaker Reset Button 4. If the Grinder still does not turn on, check that the electrical wall outlet is properly working.
PAGE 8
PRIOR TO USE Disassemble the Grinder Head and wash each part thoroughly in warm water, taking particular care to remove all grease and oil from surfaces. Dry all parts thoroughly before re-assembling. DO NOT IMMERSE THE MOTOR IN WATER OR OTHER LIQUIDS! 8. Hold the casing in place with one hand while feeding the sausage mixture through the Grinder. As the meat fills the casing, gently lay it on a clean, dry surface. NOTE: When using natural casings, use a wet surface. 9. Do not fill the last 3”-4” (7.
PAGE 9
STUFFING INSTRUCTIONS GRINDER ASSEMBLY INSTRUCTIONS WARNING! Before cleaning, assembling or disassembling the Grinder, make sure the PLUG IS REMOVED FROM THE OUTLET/POWER SOURCE! ALWAYS unplug the Grinder when not in use. 1. After grinding the meat following the “Grinding Instructions”, mix the ground meat with the sausage seasonings. 2. Follow the “Stuffer Assembly Instructions” or the “High-Speed Stuffer Assembly Instructions” to fully assemble the Grinder as a Stuffer including the Tray.
PAGE 10
7. Insert the neck of the Tray into the Feed Chute (Figure 3). 7. Insert the neck of the Tray into the Feed Chute (Figure 12). Tray 8. NEVER operate Grinder without the Tray secured in place (Figure 4). Neck REFER TO “GRINDING INSTRUCTIONS” FIGURE 3 8. NEVER operate Grinder without the Tray secured in place (Figure 13). Neck REFER TO “STUFFING INSTRUCTIONS” Feed Chute FIGURE 12 Feed Chute Head Head Tray Tray FIGURE 4 WARNING! WARNING! NEVER operate Grinder without the Tray secured in place.
PAGE 11
HIGH-SPEED STUFFER ASSEMBLY INSTRUCTIONS GRINDING INSTRUCTIONS WARNING! WARNING! Before cleaning, assembling or disassembling the Grinder, make sure the PLUG IS REMOVED FROM THE OUTLET/POWER SOURCE! ALWAYS unplug the Grinder when not in use. NOTE: The High-Speed Stuffing System is designed for use with the 10 mm Funnel ONLY. DO NOT attempt to use the HighFeed Speed Plastic Auger with any other Funnels. Chute SERIOUS DAMAGE to the Grinder Head and other components may occur.
PAGE 12
7. Insert the neck of the Tray into the Feed Chute (Figure 8). STANDARD STUFFER ASSEMBLY INSTRUCTIONS 8. NEVER operate Grinder without the Tray secured in place (Figure 9). WARNING! Before cleaning, assembling or disassembling the Grinder, make sure the PLUG IS REMOVED FROM THE OUTLET/POWER SOURCE! ALWAYS unplug the Grinder when not in use. 1. Insert the Head into the Gear Housing with the feed chute of the Head facing straight Feed up.