ASSEMBLY INSTRUCTION E176-T TV STAND A Top Glass E 1pc Side Frame - L / R I 2pcs Drawer Front M 1pc Drawer Bottom Q 1pc Bolt Ø1/4"x70mm U 4pcs Screw M3x10mm 12pcs B Bottom Glass F 2pcs Middle Panel - L / R J 2pcs Drawer Back N 1pc Leg R 4pcs Bolt Ø1/4"x32mm V 4pcs Flat Washer Ø1/4"xØ12x1.5mm C Metal Frame G 2pcs Back Panel K 1pc Drawer Side - Left O 1pc Slide Rail S 1pc Bolt Ø1/4"x22mm W 4pcs Lock Washer Ø1/4xØ10x1.
Y Sucking Disc Z Screwdriver Ø12x4mm (Not Provided) 16pcs 1pc This page lists all the contents included in the box. Please take the time to identify the hardware as well as the individual components to this product. As you unpack and prepare for assembly, place the contents on a carpeted or padded area to protect them from damage.
1 Attach the Drawer Side - Left (K) & Drawer Side - Right (L) to Drawer Front (I), using Screw (T) and tighten with Screwdriver (Z). T 4pcs Z L I T T K Z (Not Provided) 2 Put Drawer Bottom (M) into Drawer Side - Left (K) & Drawer Side - Right (L) and Drawer Front (I).
3 Pull out Slide Rail (O) fully extended, a hold-in detent can be seen or touched on slide runners. Lift the detent up and pull out to separate. O O-1 4 O-2 Attach the Drawer Side - Left (K) & Drawer Side - Right (L) to Drawer Back (J), using Screw (T) and tighten with Screwdriver (Z). Attach the one of Slide Rail (O) to Drawer Side - Left (K) & Drawer Side - Right (L) using Screw (U) and tighten with Screwdriver (Z).
Attach the Drawer Front (I) to Drawer Panel - Front (H) using Bolt (S), Flat Washer (V), then tighten with Screwdriver (Z). S 4pcs V 4pcs Z V S H V Z (Not Provided) 6 S I V Attach the other one of Slide Rail (O) to Middle Panel - L / R (F), using Screw (U) and tighten with Screwdriver (Z).
7 Assemble the Leg (M) to the bottom of Side Frame - L / R (E) as below shown. E (L / R) x2 M 8 Attach the Middle Panel - L / R (F) to one of Metal Frame (C) using Bolt (P), Lock Washer (W) and Flat Washer (V) by Allen Key (X), put Back Panel (G) into Middle Panel - L / R (F) and Metal Frame (C).
Attach the Middle Panel - L / R (F) to the other one Metal Frame (C) using Bolt (P), Lock Washer (W) and Flat Washer (V) by Allen Key (X), attach the Front Cross (D) to Metal Frame (C) using Bolt (P), Lock Washer (W) & Flat Washer (V) by Allen Key (X). 9 C V D P P X W P 10pcs V 10pcs W 10pcs X P C D F P P P P P P 10 Attach the Metal Frame (C) to Side Frame (E) using Bolt (Q) & Bolt (R), Lock Washer (W), and Flat Washer (V) by Allen Key (X).
11 Put the Sucking Disc (Y) to Metal Frame (C), then put Top Glass (A) & Bottom Glass (B) onto Metal Frame (C) with Sucking Disc (Y). Y 16pcs Y A C B C B 12 Attach the assembled drawer to Middle Panel - L / R (F) by using Slide Rail (O). Move slide ball spacers to front. Hold drawer horizontally, and slide runners into ball spacers. Remark: If there is any gap between the legs and ground, please adjust the leveler until it reaches the ground.
