CANOPY RANGEHOOD WRC604WC
CONGRATULATIONS CONTENTS Dear Customer, Important safety instructions Description of your rangehood Components list Technical specifications Rangehood dimensions Installation Using your rangehood Care & maintenance Troubleshooting Warranty Congratulations and thank you for choosing our canopy rangehood. We are sure you will find your new rangehood a pleasure to use.
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS(CONTINUED) Electrical connection This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
PRODUCT DESCRIPTION WRC604WC Flue cover mounting bracket Top flue cover Bottom flue cover Exhaust duct (source locally) Damper Hood body 2 Filter Fig.3 Additional items required for installation Technical specification Fixings required to attach rangehood body and anti tilt brackets Power supply: AC 220~240V 50Hz.
RANGEHOOD DIMENSIONS Fig.
INSTALLATION Pre-installation Installation Before installing the rangehood, peel off any protective coating and remove the filters. 1. Location Using a spirit level mark a vertical centre line on the wall where the hood is to be positioned, and a horizontal line at the hood base position. NOTE: The height of the underside of the hood body must be a minimum of 600mm* to a maximum height of 800mm. The hood is to be mounted on the wall.
INSTALLATION 3. Install flue cover wall mounting brackets with suitable fasteners. Suitable fasteners must be used for rangehood mounting points . Refer to Fig.5 for dimensions. If installation is for recirculation mode refer to Item 6a and Fig.9. Depending on the preferred installation/ducting mode, follow step 6a or 6b below. 6a. Recirculating mode(Fig.9) Fix the T-piece to the top mounting bracket by using the 4 screws supplied as dimension indicated Fig 5. Adhere two sponge to the outlet of T-piece.
INSTALLATION 6b. Ducted mode (Fig.11) insert flexible pipe and secure flue tape to air outlet with suitable duct tape. 9. Slide flue cover to upper position and fix with screws provided . NOTE:f or ducted mode we recommended to extend the flue pipe through the roof cladding(with appropriate flashing) to an external roof cowl, venting the exhaust externally. To ensure optimum performance of the rangehood, the use of bends should be avoided. Straight, rigid and short ducting is recommended to use.
USING YOUR RANGEHOOD Best results are obtained by using a low speed for normal conditions and high speed when odours are concentrated. Turn on the hood on a few minutes before you start cooking. The hood should be left on for a minimum of 5 minutes after cooking or until all odours have dispersed. The control switch are located on the front of the unit.
CARE & MAINTENANCE Hand washing Changing the LED lamps Soak grease filter for about one hour in hot water with a grease-loosening cleaner, then rinse off thoroughly with hot water. Repeat the process if necessary. Refit the grease filters when they are dry. If LED lamps need replacing, they must be replaced by lamps as stated in the technical specifications. Dish washer Remove the lamp cover by releasing the screw and replace the new E14 LED lamps. Place grease filters in the dishwasher.
TROUBLESHOOTING GUIDE PROBLEM The cooker hood does not start SOLUTION Check that the hood is connected to an electrical supply Check that a fan speed has been selected Check that a fan speed is set high enough for the task The grease filters are clean The kitchen is adeqeuatly vented to allow the entry of fresh air Poor extraction If set up for recirculation, check that charcoal filter is still effective If set up for extraction, check the ducting and outlets are not blocked The safety cut-out device has
For more information on all Westinghouse appliances, or for dimension and installation information, call into your retailer, phone or email our customer care team or visit our website: AUSTRALIA phone: 13 13 49 email: customercare@electrolux.com.au web: westinghouse.com.au NEW ZEALAND phone: 0800 10 66 20 email: customercare@electrolux.co.nz web: westinghouse.co.nz and WESTINGHOUSE are trademarks of Westinghouse Electric Corporation. Used under license. All Rights Reserved.
