INSTALLATION & USER MANUAL CANOPY RANGEHOOD WRC613SB, WRC913SB, WRC614SC, WRC914SC
CONGRATULATIONS CONTENTS Dear Customer, Important safety instructions........................................................3 Congratulations and thank you for choosing our canopy rangehood. We are sure you will find your new rangehood a pleasure to use. Before you use your rangehood, we recommend that you read through the whole user manual, which provides the description of the rangehood and its function. Description of your rangehood ....................................................
IMPORTANT SAFETY INSTRUCTIONS This manual explains the proper use of your new Westinghouse canopy rangehood. Please read this manual carefully before using the product. This manual should be kept in a safe place for handy reference. This canopy rangehood is a domestic appliance which has been manufactured and tested to comply with Australian and New Zealand Standard AS/NZS 60335.2.31.
IMPORTANT SAFETY INSTRUCTIONS (CONTINUED) Electrical connection Check that the mains voltage matches with the voltage on the data plate inside the canopy rangehood. Check that the installation complies with standards of local building, gas and electrical authorities. Before connecting to the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate inside the cooker hood.
PRODUCT DESCRIPTION Components list Qty. 1 Telescopic flue cover set 1 2 Upper Flue mounting bracket 1 3 Lower Flue mounting bracket 1 4 Exhaust transition duct 1 5 Main body and fan housing assembly 1 6 Grease filter(WRC613SB) 2 6 Grease filter(WRC913SB) 3 1 2 3 4 5 6 Fig. 3 Additional items required for installation Technical specification · Fixings required to attach rangehood body and anti tilt brackets · Power supply: 240 V 50 Hz.
RANGEHOOD DIMENSIONS RANGEHOOD DIMENSIONS RANGEHOOD DIMENSIONS WRC613SB/WRC614SC WRC913SB/WRC914SC WRC613SB WRC913SB WRC613SB 320 520 600 320 500 320 290 625 Min625 660 / Max1160 Min 660 / Max1160 520 600 290 320 290 625 Min625 660 / Max1160 320 290 320 Min 660 / Max1160 WRC913SB 780 900 500 780 900 320 500 320 500 Fig. 4 Fig. 4 Fig.
INSTALLATION Pre-installation Before installing the cooker hood, peel off any protective plastic covering and remove polystyrene from inside behind the fan motor. See Fig. 5 below Fig. 5 Location The hood is to be mounted on the wall. When installed, the hood must be not less than 60cm above electric burners or 65cm above gas or mixed-fuel burners.
INSTALLATION 1. Using a spirit level mark a vertical centre line on the wall where the hood is to be positioned, and a horizontal line at the hood base position. (See Fig. 4, or 5 for relevant model. NOTE : The height of the underside of the hood body must be a minimum of 600mm* to a maximum height of 800mm . 8 * If the instructions of the hob specify a greater distance than the minimum above, then that shall be the minimum height for installation. 2.
INSTALLATION 3. Install flue cover wall mounting brackets with suitable fixings. Install suitable screws for rangehood mounting points (to support a total weight of 30kg) to the wall as marked (Fig. 7) 5. Hang the body hood on the mounting screws then secure at the anti-tilt locations as indicated in Fig 9 Fig. 9 Fig. 7 2 mm 4. Fix exhaust transition duct using screws supplied (Fig. 8) Fig.
INSTALLATION Depending on the preferred installation/ducting mode, follow step 14a or 14b below. 6a. Recirculating mode (Fig. 10). Using the centre line, secure the recirculating T-piece to the wall with suitable screws/fixings (optional kit AR610RK). Install flexible pipe between T-piece and reducer. Use cable ties or suitable duct tape to secure flexible pipe to T-piece and reducer (Fig.
INSTALLATION 7. Electrical connection 9. Fix upper flue cover Check that the installation complies with the standards of local building, gas and electrical authorities. Before connecting to the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate inside the rangehood. Fix upper flue cover to the wall mounting bracket with screws supplied. Ensure that the upper section is extended. Fig. 14 Fig. 13 8.
CONTROL PANEL CARE & MAINTENENCE • Best results are obtained by using a low speed for normal conditions and a high speed when odours are more concentrated. • Turn the hood on for a few minutes before you start cooking. • The hood should be left on for a minimum of 5 minutes after cooking or until all odours have dispersed. • The control switches are located on the front panel of the unit. See Fig. 16 below. Fig. 16 A.
CARE & MAINTENENCE Hand washing Changing the LED lamps Soak grease filters for about one hour in hot water with a grease-loosening cleaner, then rinse off thoroughly with hot water. Repeat the process if necessary. Refit the grease filters when they are dry. If LED lamps need replacing, they must be replaced by lamps as stated in the technical specifications. Dishwasher Place grease filters in the dishwasher. Select the most powerful washing program and highest temperature, at least 65°C.
TROUBLESHOOTING GUIDE PROBLEM The cooker hood will not start REMEDY Check that the hood is connected to an electrical supply Check that a fan speed has been selected Check that the fan speed is set high enough for the task The grease filters are clean The kitchen is adequately vented to allow the entry of fresh air The cooker hood is not working If set up for recirculation, check that the charcoal filter is still effective If set up for extraction, check that the ducting and outlets are not blocked Do
OPTIONAL DUCTING ACCESSORIES AR150RC AR150F AR150WV AR610RK AR150FD AR125FD AR610CF PART NUMBERS DESCRIPTION AR150RC 150mm G/Bond Roof Cowl AR150F 150mm G/Bond Flue 1200m AR150WV 150mm Wall Vent & duct AR610RK Recirculating kit (150–120m reducer, T-piece & carbon filters) AR610CF Replacement carbon filter AR610FS Stainless steel exhaust cover extension 1200mm AR150FD 150mm aluminum flexible duct AR125FDA 125mm aluminum flexible duct 1438124 50mm wide aluminum tape (55m roll) OPTIO
NOTES 16
NOTES NOTES 17
NOTES
Warranty FOR SALES IN AUSTRALIA AND NEW ZEALAND APPLIANCE: WESTINGHOUSE RANGEHOODS This document sets out the terms and conditions of the product warranties for Westinghouse Appliances. It is an important document. Please keep it with your proof of purchase documents in a safe place for future reference should there be a manufacturing defect in your Appliance. This warranty is in addition to other rights you may have under the Australian Consumer Law. 1.
For more information on all Westinghouse appliances, or for dimension and installation information, call into your retailer, phone or email our customer care team or visit our website: AUSTRALIA phone: 13 13 49 email: customercare@electrolux.com.au web: westinghouse.com.au NEW ZEALAND phone: 0800 436 245 email: customercare@electrolux.co.nz web: westinghouse.co.nz and WESTINGHOUSE are trademarks of Westinghouse Electric Corporation. Used under license by Electrolux Home Products Pty Ltd.
