User Manual

14 15REMOVING FEATURESINSTALLATION
ICE AND WATER INSTALLATION
TIPS & INFORMATION
IMPORTANT
• Always fit the filter as per manufacturer’s instructions.
• If you need to replace water tube, only use approved water quality piping that meets the pressure requirements.
• Make sure your refrigerator is level to avoid uneven ice cubes.
• Replace filter at suggested intervals to avoid water/ice reduction and irregularities in taste.
• Remove and clean ice bin once a month, discarding unused ice cubes. This will ensure fresh, clean ice and smooth
operation of your ice maker.
• Clean and empty the dispenser drip tray regularly to avoid overflow.
WARNING
WARNING
If you have not used the dispenser for some time, discard the first seven or eight cups of water and any ice that the
ice maker produces in the first 24 hours (contaminants could have settled in the water pipes).
Water filter
The water filter is located at the top left side of the fresh food
compartment.
Replacing the water filter
You should change the water filter every six months to ensure the
highest possible water quality.
If your refrigerator has not been used for a period of time (during
a house move for example), change the filter before reinstalling
the refrigerator.
It is not necessary to turn the water supply off to change the filter.
Be ready to wipe up any small amounts of water released during the
filter replacement.
1. Ensure that the ice maker is turned off (Diagram 1).
2. Remove the filter by turning anti-clockwise 180˚.
3. Slide the old water filter cartridge straight out of the housing and
discard it. (Diagram 2).
4. Unwrap the new filter cartridge and using the alignment guide,
slide it gently into filter housing until it stops against the filter
connection at the back of the housing. (Diagram 3).
5. Engage the filter by firmly rotating clockwise until the filter snaps
into position (once engaged the filter cannot be rotated further).
(Diagram 4).
6. Press a drinking glass against the water dispenser while checking
for any leaks at the filter housing. Any spurts and sputters that
occur as the system purges air out of the dispenser system
are normal.
7. After filling one glass of water, continue flushing the system for
about four minutes.
8. Turn on the ice maker. (Diagram 5).
9. When the filter has been replaced press and hold the ‘Ice and
Water’ button for three seconds to reset the filter replace timer.
PureSource
Ultra 2
Ice & Water Filtration System
PureSource
Ultra 2
Ice & Water Filtration System
PureSource
Ultra 2
Ice & Water Filtration System
Diagram 2
Diagram 3
Diagram 4
Diagram 1
Diagram 5
USING YOUR REFRIGERATOR
Refrigerators work by transferring heat from the food
inside to the outside air. This operation makes the back
and sides of the refrigerator feel warm or even hot
particularly at start-up and on warm days – this is normal.
Avoid placing food against the air vents in the refrigerator
as it affects efficient circulation. If the door is opened
frequently, a light frosting will occasionally occur on the
freezer’s interior. This is normal and will clear after a few
days. If the freezer door is accidentally kept open, a heavy
frost will coat the inside walls and should be removed.
Your new refrigerator uses a high-speed compressor,
along with other energy-efficient components, which may
make unusual sounds and be more noticeable at night
and quieter times. These sounds simply indicate your
refrigerator is working how it should. They include:
• Compressor running noises;
• Air movement noise from the small fan motor;
• A gurgling sound, similar to water boiling;
• A popping noise, heard during automatic
defrosting; and
• A clicking noise, prior to compressor start-up.
Further details can be found in the Troubleshooting Guide.
TIPS & INFORMATION
IMPORTANT
For top mount refrigerators (where the freezer is
on top of the fresh food compartment).
• Don’t place food forward of the ribs on the freezer
floor, as it will keep the door open.
Ribs
For bottom mount refrigerators (where freezer is below
the fresh food compartment):
• Ensure all freezer drawers and shelves are pushed
back completely to prevent them from keeping the
door open.
Crisper Bin
Removal (standard Crisper Bins):
1. Empty food from the crisper. On some models it will
be necessary to remove the bottle storage bins.
2. Remove the crisper bin(s) by pulling forward, then up
and forward again.
3. For top mount and single door, remove the crisper
shelf by lifting the catches on the left and right
underside of the shelf and pulling the shelf forward.
SpillSafe™ glass shelves
To remove the shelves,
gently pull them forward
until the shelf comes
clear of the shelf guides.
To return the shelf, make
sure there is nothing
behind that may obstruct
movement. Gently push the
shelf, into the cabinet and
back into position.
Freezer shelf
Remove the freezer shelf
by lifting the catches on
the right and left underside
of the shelf to release the
shelf then pull the shelf
toward you.
REMOVING FEATURES
CATC H