Installation and Assembly: Universal Flat Wall Mount for 22" - 37" Screens Model: MT80 THIN Features: • Universal design for 22" to 37" plasma and LCD screens • Low-profile design keeps the screen close up against the wall Visit the Westinghouse Web Site at www.westinghousedigital.com R Max Load Capacity: 80 lb (36.3 kg) For customer service call 1-866-287-5555.
Note: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Westinghouse product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer service at 1-800-729-0307. • Make sure that the wall will safely support the combined load of the equipment and all attached hardware and components.
Before you begin, make sure all parts shown are included with your product. Parts List AA BB CC DD EE FF Description Qty wall plate 1 adapter bracket 2 #14 x 2.5" wood screw 4 M5 x .8 x 25 mm socket head cap screw 2 Alligator® anchor 4 4 mm security allen wrench 1 MT80 THIN Part # 200-4629 200-4628 5S1-015-C04 520-9567 590-0097 560-1145 AA BB FF DD EE CC 3 of 8 Visit the Westinghouse Web Site at www.westinghousedigital.
Installation to Single Wood Stud Wall WARNING • Installer must verify that the wall will safely support four times the combined weight of all attached equipment and hardware. 1 Use stud finder to locate stud centers. Place wall plate (AA) on wall as template, level wall plate and mark center of studs with pencil. Drill three 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Attach wall plate (AA) using three #14 x 2.5" wood screws (CC). Skip to step 2 on page 7.
Installation to Double Wood Stud Wall WARNING • Installer must verify that the wall will safely support four times the combined weight of all attached equipment and hardware. 1 Use stud finder to locate stud centers. Place wall plate (AA) on wall as template, level wall plate and mark center of studs with pencil. Drill four 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Attach wall plate (AA) using four #14 x 2.5" wood screws (CC). Skip to step 2 on page 7.
Installation to Solid Concrete or Cinder Block WARNING • When installing Westinghouse wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifications.
Note: Before starting this step refer to accompanying instruction sheet to install adapter brackets to flat panel screen. Installing Flat Panel Screen to Wall Plate 2 Insert two M5 x 25 mm socket head cap screws (DD) into mounting brackets (BB) and tighten a few turns to hold in place as shown in detail 1. Hang screen by the mounting brackets (BB) on wall plate (AA) as shown below. Make sure screen is safely hooked on mount before letting go. Screen can be adjusted horizontally if desired.
Limited Five-Year Warranty Westinghouse Digital Electronics warrants to original end-users of this Westinghouse television mounting product (the “Product”) that the Product will be free from defects in material and workmanship, under normal use, for a period of five (5) years from the date of purchase by the original end-user, subject to the following terms and conditions: REPAIR OR REPLACEMENT – For a period of five (5) years from the original date of purchase, Westinghouse Digital Electronics will repair
Installing Adapter Brackets to the Flat Panel Screen Model: MT80 THIN Begin with product installation and assembly manual before reading this instruction manual. Parts List A C E F G H I K O S V Description Qty. Part # M4 x .7 x 12 mm phillips screw 6 504-9013 M4 x .7 x 25 mm phillips screw 6 504-1015 M5 x 40 mm pan head phillips scew 4 520-1199 M6 x 25 mm pan head phillips screw 4 520-1208 M6 x 1 x 20 mm pan head phillips screw 4 520-9402 M5 x .
To assemble the adapter brackets to your screen, begin with the table on pages 2 and 3. Find the configuration that corresponds to your screen. Refer to the configuration table on page 3 to install the adapter brackets. Notes: The Universal Flat Wall Mount is a universal mount which accommodates a wide variety of screens. If your particular screen is not listed on pages 2 and 3 or unsure which configuration matches your screen, please contact customer service to ensure product compatibility.
Sony Sony Studio Experience Syntax Syntax Tatung Tatung Tatung Toshiba Toshiba Toshiba ToteVision ViewSonic ViewSonic Viewsonic Viewsonic Viewsonic Westinghouse Westinghouse Westinghouse Westinghouse Westinghouse Westinghouse Westinghouse Zenith Zenith Screen Size 32" 32" 30" 27" 30" 23" 27" 30" 26" 26" 32" 22" 22.
Installing Adapter Brackets 2 To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached. Place adapter brackets (BB) on back of screen, align to holes, and center on back of screen as shown in figure 2.1. Refer to step 1 to determine the proper fasteners to use.
