Instruction Manual

ITEM: LV0BAA01H-08
For additional help and information regarding installation, contact Customer Service at 1-877-723-0723, 8am-5pm,CST Monday – Friday
[e-mail]
and Westinghouse are trademarks of Westinghouse Electric Corporation. Used under license by Sky Rich Star Limited. All Rights Reserved.
E
TROUBLESHOOTING
OPERATING
PROBLEM
POSSIBLE CAUSE
CORRECTIVE ACTION
The light does
not turn on
when needed.
1. The wire of the connector
doesn’t contact pins.
2. The wire and the transformer
aren’t in contact.
3. No power to the transformer.
1. Check the wiring of connector. Make sure
brass contact pins pierce the plastic wire
insulation and are touching the copper
wires inside.
2. Check the connection between the
primary wire and the transformer.
3. Check the power to the transformer.
WARNING:
1. Fixture shall be connected to an extra low voltage transformer approved for use with landscape
lighting systems.
2. This fixture is to be connected to a secondary wiring of the following type:
SPT-3 suitable for outdoor use; or
approved landscape lighting cable.
3. If you have any doubts about how to install this lighting fixture, or if the fixture fails to operate
completely, please contact a licensed electrical contractor.
PACKAGE CONTENTS
INSTRUCTIONS
MOUNTING
1. Put notched pipe thread (D ) cover the wire cord. Connect the charging pole (B) and ground stake
(C) together with notched pipe thread (D). (figure 1)
2. Align the assembly (B,C&D) with the charging port of the light fixture (A) and tighten it clockwise.
(figure 2)
3. Push the assembled fixture into the ground. (figure 3)
NOTE: DO NOT use a hammer. NEVER push the fixture into the ground by the head. Instead, hold
the pole (B) and push the fixture into the ground.
4. TURN OFF POWER. Connect fixture’s 12V cable to transformer landscape wire run using supplied
wire connector. Make wire connections using supplied. Quick connect following instructions, or
using other approved wiring connection method (not supplied.)
A: Light Fixture D: Notched Pipe ThreadC: Ground StakeB: Charging Pole
figure 7
figure 8
1. Unscrew the top cover from the connector (E) and keep it for later use. (figure5)
Bottom base
Top cover
E
E
Top cover
Bottom base
Transformer wire
Wire
Brass pins
figure 5 figure 6 figure 7
NOTE:
a. The brass pins must be aligned to the center of wires and tightened. (figure 7)
b. This fixture is a safety low-voltage (AC12V), and the brass pins can be exposed but pose no danger of electric shock.
3. Assembly is complete. Refer to the transformer’s instructions for how to install additional lighting (sold separately)
to the same transformer.
2. Insert wire from low-voltage transformer (sold separately) into the bottom base of connector (E) and then re-tighten
the top cover removed in step 1 until the contact pins completely pierce the plastic shield of the wire. (figure 6)
QUICK CONNECT INSTRUCTIONS
RECHARGEABLE BATTERY
This product includes a 3.7V 2000mAh lithium (18650) rechargeable battery and cannot be
replaced.
WARNING: Do not dispose of lithium batteries in municipal waste stream or by fire as batteries
may explode. Do not open, short circuit, or destroy batteries. Dispose of batteries in accordance
with Local, State, and Federal regulations. Do not mix old and new batteries. Do not mix alkaline,
standard (carbon-zinc), or rechargeable (nickel cadmium, nickel metal hydride or lithium ion)
batteries .
TRADEMARK ATTRIBUTION FOOTNOTE
NOTE:
The Bluetooth® brand elements may not be used in a fashion or manner that could impair or
otherwise damage the goodwill associated with the Bluetooth® brand or the Fellow Adopters
(Sky Rich Star Limited). The Bluetooth® brand elements shall therefore not be used in connection
with products and services that do not enable any Bluetooth® wireless functionality or in connection
with unlawful, obscene, pornographic, excessively violent, hazardous,or otherwise poor-taste
activities.
Whenever the Bluetooth Trademarks are used in a particular piece , they must be attributed with an
appropriate trademark footnote. The recommended attribution footnote is as follows:
“The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. And
any use of such marks by Sky Rich Star Limited is under license. Other trademarks and trade names
are those of their respective owners.”
FCC WARNING
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance
could void the user authority to operate the equipment.
Notes: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency enerqy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
HOW TO OPERATE THE SPEAKER PATH LIGHT:
Press Light Button (F) to turn on the light for high light output (50 LM). Press again
for medium light output (10 LM) and one more time for off.
HOW TO OPERATE POWER / BLUETOOTH ACTIVATION BUTTON :
1. Press Power / Bluetooth® Activation Button (G) to turn on speaker and activate
bluetooth® function.
2. Bluetooth® Speaker will enter pairing mode. Activate bluetooth® on your device
and find device named “LV0BAA01H-08”. Press to pair.
3. Once paired, select audio from your device and play through the light speaker.
4. When Bluetooth® is activated, light will quickly flash during pairing mode and
be solid blue when paired.
5. Press Power / Bluetooth® Activation Button (G) quickly to pause or play music.
6. Press Power / Bluetooth® Activation Button (G) for 2 seconds to turn off speaker.
7. Connection distance within 20 meters of open environment. If the Bluetooth
is disconnected, the speaker will shut down automatically after 10 minutes.
NOTE:
Adjust the volume with your device.
F: Light Button
G: Power / Bluetooth®
Activation Button
figure 1 figure 3 figure 4figure 2
Charging Port
5. Remove the light fixture (A) from the charging pole (B) and use it independently on the table.
(figure 4)
E: Quick Connect
TWO CHARGING MODES:
1. The light can be charged by 5V USB adapter through the USB charging port.
Color-indicator light will be red while charging and will turn off upon unit
reaching a full charge.(figure 7)
2. The light powered by external 12V AC/DC power supply through the
charging port.
Charging Port
USB Charging Port
WHEN INSTALLING LIGHTING (LINE VOLTAGE OR LOW VOLTAGE), CARE SHOULD BE TAKEN TO KEEP
CLEAR OF POTENTIALLY COMBUSTIBLE MATERIALS. WHEN MAINTAINING THE FIXTURES, BE SURE TO
REMOVE LEAVES, PINE NEEDLES, GRASS CLIPPINGS, MULCH, OR ANY DEBRIS THAT HAS
ACCUMULATED ON THE LIGHT BULB, LENS, OR BODY OF THE FIXTURE.