INSTALLATION MANUAL REFRIGERATION IK009 INTEGRATION KIT WTB4600, WTB4604, WTB5400, WTB5404, WBE4500, WBE4502, WBE4504, WBE5300, WBE5304, WFB4204, WRB5004 Also suitable on selected Electrolux and Kelvinator 400L - 500L Tom Mount, Bottom Mount and Single Door Fridges and Freezers
westinghouse.com.au CONGRATULATIONS CONTENTS Congratulations and thank you for choosing our integration kit. Before you install the integration kit, we recommend that you read through the entire installation manual. General warnings .......................................................... 2 Refrigerator integration kit items............................ 3 Cupboard dimensions ..................................................
DESCRIPTION REFRIGERATOR INTEGRATION KIT ITEMS Because this kit is common to a variety of models, you need to select the items required to suit your model. Please be sure to identify the correct slide-housing part (see below), depending on whether your fridge has a curved door or a flat door. The slide-housing part which is not required for your particular model can be discarded. All other parts in this pack are required for installation.
westinghouse.com.au DIMENSIONS CUPBOARD DIMENSIONS IMPORTANT! Pages 4, 5, 6, and 7 should be given to the person responsible for cupboard design and construction. The cupboard dimensions required for each model are shown on page 5, 6 & 7. 1. All sizes are internal and measured in millimetres. 2. It is important to ensure that the correct cupboard sizes are used to ensure adequate air flow around the refrigerator. 3. Cupboard hinges should be a 120° opening type. (Use hinges supplied). 4.
NOTE: All sizes are internal and measured in millimetres. For ‘lettered’ dimensions refer to the table on page 4.
westinghouse.com.au DIMENSIONS (CONTINUED) When positioned in a corner the clearance of Dim G on the hinge side of the cabinet will allow the doors to be opened enough to enable the removal of the crisper bins. Clearances When installed the refrigerator needs to have adequate air ventilation. It is important to ensure there is good airflow from the front to underneath and up the rear to the top of the cabinet (see diagrams).
INSTALLATION INSTALLATION OF 120˚ HINGE Use screws attached to mounting plate to attach the hinge to the cabinet. Please follow the instructions below to install the 120º hinge. cabinet cupboard door 37mm mounting plate 120º hinge This dimension is typically 37mm (from centre line of mounting plate to the cupboard cabinet edge) Attach mounting plate with 120º hinge and tighten the screw. Preparation 120º hinge screw mounting plate Plastic roller nut Use self tapping wood screws P No.
westinghouse.com.au INSTALLATION (CONTINUED) ATTACHING THE REAR ROLLERS Once fitted turn the adjusting nut on each roller assembly anti-clockwise three full turns, this will raise the cabinet at the rear by approximately 12mm (ensure that the nut is completely wound up before turning). A set of adjustable back feet/rollers is provided in the kit. These are required to ensure that the product is levelled correctly, failure to fit these may result in the poor operation of door opening. 1.
ATTACHING THE TOP HINGE BRACKET ATTACHING SLIDE-HOUSING TO REFRIGERATOR DOORS 1. Remove top hinge cover (Figure 3), cover clips off. 2. Remove the three (3) top hinge screws. 3. Elevate hinge. 4. Slide the top hinge bracket into position below the hinge. 5. Re-attach hinge and screws ensuring that refrigerator door is still correctly positioned. 1. Ensure slide-housing is positioned squarely as shown. 2. Ensure that the slide-housing is positioned on the door as shown in the diagrams.
westinghouse.com.au INSTALLATION (CONTINUED) 360mm 100mm 235mm 235mm 235mm 100mm 235mm 100mm 2 door bottom freezer 2 door top freezer ...and secure with tape.
NOTE: For single door models, the door handle must be completely removed to provide clearance to the cupboard door and the resulting handle mounting holes hidden with a cover. Installer must use a tape or plastic cover that suits the installation appearance (not supplied). 3. While the slide-housing is taped in position, punch a small hole in the refrigerator door skin corresponding to the four (4) holes in the housing (Figure 5). 4.
westinghouse.com.au INSTALLATION (CONTINUED) REFRIGERATOR ALIGNMENT Figure 9a - Hinge side Position the refrigerator in the cupboard so that: 1. Top hinge bracket is against cupboard wall (Figure 8). 2. Front of refrigerator cabinet (with doors open) is parallel to and approximately 100mm from the front of the cupboard (Figure 9). 3. Position bottom location brackets as shown (Figures 9 & 9a). Fit foot in appropriate hole as shown and level refrigerator. (Figure 10).
SECURING THE REFRIGERATOR IN THE CUPBOARD ATTACHING SLIDE-BAR TO THE CUPBOARD DOOR NOTE: When attaching all screws to cupboard, first drill a 2mm pilot hole in the correct position. This will allow easy hand insertion of self tapping screw. 1. Fully open cupboard door (120°). 2. Open refrigerator door until it rests against the cupboard door. 3. Position slide-bar in slide-housing so that all three holes are visible when both doors are fully open (120°).
westinghouse.com.au INSTALLATION (CONTINUED) 5. Rotate slide-bar to lower alignment, mark a line on cupboard door (Figure 16). Figure 16 8. Figure 16 Secure slide-bar by driving a cupboard screw into the centre of the inner slot Fig 19. Gently test closing the door. Figure 19 6. Remove slide-bar and draw line to indicate central alignment (Figure 17). Figure 17 9.
1 0. Open and close the door a number of times. If the action is not smooth, loosen the screws and re-adjust the slide bar. Once the desired smooth action is achieved attach the central locking screw Fig 21. Figure 21 Repeat this procedure for the second slide bar if necessary. This completes the installation procedure. Customers please note.
For more information on all Westinghouse appliances, or for dimension and installation information, call into your retailer, phone or email our customer care team or visit our website: AUSTRALIA Electrolux Home Products Australia Phone: 13 13 49 Email: customercare@electrolux.com.au Website: westinghouse.com.au NEW ZEALAND Electrolux (NZ) Limited Phone: 0800 436 234 Email: customercare@electrolux.co.nz Website: westinghouse.co.nz and WESTINGHOUSE are trademarks of Westinghouse Electric Corporation.
