UNDER CABINET RANGE HOOD OWNER’S MANUAL # QR098 / 4578600 # QR083 / 4578601 # QR099 / 4578602
Table of Contents Table of Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warranty One Year Limited Warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Warranty Claim Procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety Information (continued) COOKING SAFETY INFORMATION WARNING: To reduce the risk of fire, use only metal duct work. Never use plastic duct work. 1. Never leave the range hood unattended when in use. 2. Never cook over open flames under the range hood. WARNING: To reduce the risk of fire or electric shock, do 1. Always turn the range hood on when cooking at high heat or when cooking flaming foods. not use this range hood with with any external solid state speed control device. 2.
Warranty ONE YEAR LIMITED WARRANTY A thorough inspection must be made before installation and any damage must be promptly reported. We will not be liable for failures or damage that could have been discovered or avoided by proper inspection and testing prior to installation. Conglom Kitchen & Bath warrants this product to be free from defects in materials or workmanship for one (1) year from the date of purchase.
Pre-Installation TOOLS/MATERIALS REQUIRED (NOT SUPPLIED) Measuring tape Level Utility knife Pencil Certified Duct Tape Adjustable wrench Phillips screwdriver Flathead screwdriver Needle nose pliers Hammer Electric drill Safety goggles Safety gloves Glue 5 CONGLOMKB.COM Please contact cs@conglomkb.com or 1-877-333-0098 for further assistance.
Pre-Installation (continued) PACKAGE CONTENTS D Part Description Quantity A Range hood 1 B Aluminum & charcoal filter 1 C Retangular damper (located inside the hood) 1 D Strips 3 HARDWARE INCLUDED NOTE: Parts not shown in actual size.
Pre-Installation (continued) PLANNING INSTALLATION Number of people required: 2 or more Carefully check the range hood for damage and for missing parts prior to installation. If there is any damage or if you are missing parts, do not proceed with the installation. Report damage and missing parts immediately. Do not dispose of packaging before you are satisfied with your new range hood. WARNING: Always wear safety goggles and gloves during installation. 1.
Pre-Installation (continued) FOLLOW THESE GUIDELINES WHEN INSTALLING DUCT WORK: -- Your venting system must vent to the outdoors either horizontally through the back wall (13) or vertically through the roof (14) (refer to Fig. 5/Fig. 6/Fig. 7). -- Calculate the total effective length of the duct work by adding the equivalent lengths in the table shown (Fig. 9). For each fitting used add the length of the equivalent straight duct used in the system.
Pre-Installation (continued) WIRING CONNECTION REQUIREMENTS DANGER: Risk of electrical shock. This range hood must be properly grounded. Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction. DANGER: Turn off the power circuit breaker or the power switch on the junction box before installing this unit.
Installation REMOVING THE ELECTRICAL KNOCK-OUT HOLE REMOVING THE VENTING HOLE (FOR EXTERIOR VENTING) -- Choose the venting hole to remove for your installation type. Use the top hole (3) for a top venting installation and the back hole (5) for a back venting installation. WARNING: Always wear safety goggles and gloves during installation. -- Choose the appropriate electrical knock-out hole to remove for your installation type.
Installation (continued) INSTALLING THE RANGE HOOD DANGER: Turn off the power circuit breaker or the power switch on the junction box before installing this unit. Touching circuitry inside the range hood while it is energized will result in death or serious injury. DANGER: If installing this unit over a gas range, turn off the gas at the source before installing or servicing this unit. -- Lift the range hood (A) up under the cabinet to determine its final position.
Installation (continued) INSTALLING THE CHARCOAL FILTER (SKIP THIS STEP IF YOU ARE USING EXTERIOR VENTING) NOTE: The charcoal filter should only be installed if you are not using an external venting system. -- Turn the filter clip to either side and lift the aluminum filter. -- Place the charcoal filter (B) in place, ensure that it covers the air outlet entirely. -- Turn the filter clip so that the end of the clip holds the filter firmly in place.
Operation NOTE: The fan and lights operate independently of each other. TURNING ON/OFF THE UNIT TURNING ON/OFF THE LIGHTS -- To turn on the fan, press the appropriate speed control switch [Low Speed (3), High Speed (1)] to select the desired level of power. Once a button is pressed, the previous speed mode will be cancelled. -- Press the light switch (4) to turn on the lights. -- Press the light switch (5) to turn off the lights. -- Press the power switch (2) to turn off the fan.
Maintenance REPLACING FILTERS DANGER: Turn off the power circuit breaker or the power switch on the junction box before performing maintenance. Touching circuitry inside the range hood while it is energized will result in death or serious injury. When filters need replacing, exchange with similar. Also replace filters that are damaged with punctures, bends, or broken frames. WARNING: Failure to replace worn out or damaged filters -- Turn off the range hood and disconnect the power.
Care and Cleaning RANGE HOOD WARNING: Failure to maintain basic standards of care and cleaning of the range hood will increase the risk of fire. The range hood should be cleaned (regularly internally and externally) to preserve its appearance and performance. Do: Do Not: -- Always clean in the direction of the grain (original polish lines). -- Do not use corrosive or abrasive detergents, steel wool, or scouring pads. These will scratch and damage the stainless steel surface.
Troubleshooting DANGER: Turn off the power circuit breaker or the power switch on the junction box before performing maintenance. Touching circuitry inside the range hood while it is energized may result in serious injury or death. Problem Solution The range hood does not operate. -- Check that the power supply cable and all electrical wiring are properly connected. -- Check that the power is turned on at the junction box or circuit breaker.
Specifications Model Dimensions QR098 QR083 QR099 Rating Control Type Max. Fan CFM 120V~60Hz 1.1A Rocker Switches 160 ± 10% 758 mm (29.8 in) W 468mm (18.4 in) D 100 mm (4 in) H Speeds High Low Light Bulb Wattage 1 x 40W Incandescent E26 base light bulb Venting Options Top venting Back venting Recirculating/ Inside venting WIRING DIAGRAM II O I I BLUE RED BLACK BLACK GRAY 6uF / 250V O WHITE BLACK 1 40W E26 L WHITE YELLOY BLACK WHITE YELLOY&GREEN 120~60Hz N 17 L CONGLOMKB.
Specifications (continued) EXTERNAL DIAGRAM OF RANGE HOOD 8 7/8” 10 1/2” 1 5/8” 1/4” 2” 3 1/8” 8 3/4” 6 1/4” 3/8” 10” 7 7/16” 4 1/16” 13 11/16” 1/2” 7/8” 9 13/16” 2 1/16” 1 9/16” 25 13/16” 1 1/16” 1 5/8” 27 3/4” 10” 9 13/16” 7 7/16” 3/8” 13/16” 7/8” 3” 1/2” 29 13/16” 16” 29 13/ 3 1/8” 9 7/8” 4” 18 7/1 6” 18
Service Parts If you are missing parts or if you require replacement parts, please contact our customer service team at cs@conglomkb.com or 1-877-333-0098 (8:30 am – 5 pm, EST, Monday–Friday). Identify the required part(s) and have the part number(s) ready.
Imported by: St-Laurent, Québec, H4S 2C3 1-877-333-0098 | cs@conglomkb.com (service available in English and French, Monday - Friday from 8:30am - 5pm EST) www.conglomkb.com Made in China and WESTINGHOUSE are trademarks of Westinghouse Electric Corporation. Used under license by Conglom Inc. All Rights Reserved.
