Installation Guide

ManualsBrandsWestinghouse ManualsLightingVapor Proof Single Light 10" Tall LED Outdoor Wall Sconce

ESF-WH-0711

2 ESF-WH-071

WARNINGS:

• Operating temperature: -22°F to 113°F (-30°C to 45°C).

• Suitable for dry and wet locations.

• This device can not be intended for use with emergency exits.

• Turn off the power before installation.

• Installation requires knowledge of electrical systems. Installation to be performed by a

qualified electrician. Don't attempt installation if not qualified.

Preparation for installation

Step 2: Insert the circuit wires through the

center hole in the mounting base.

Step 3: Drill two holes and install the mounting

base.

Step 1: Remove the pipe cap from the center

hole.

Step 5: Tighten the screws, insert end caps,

and adjust fixture body to the mounting base.

Step 4: Connect the circuit wires to the fixture

wires using wire nuts and electrical tape for a

more secure connection.

Ceiling mount: Type 1: Wires through the center hole

WIRE DIAGRAM:

Replacing HPS/HID lamp

Connect directly

AC120-277V

HPS/HID

LED

Black

White

Black

White

Remove fixture from the mounting base.

Ignitor

LED Vapor Proof Fixture

Installation Instruction

INSTRUCTION MANUAL

COMMERCIAL SERVICE

AC120-277V

Green

Summary of content (6 pages)

PAGE 1
COMMERCIAL SERVICE Preparation for installation INSTRUCTION MANUAL Remove fixture from the mounting base. LED Vapor Proof Fixture Installation Instruction Ceiling mount: Type 1: Wires through the center hole WARNINGS: • Operating temperature: -22°F to 113°F (-30°C to 45°C). • Suitable for dry and wet locations. • This device can not be intended for use with emergency exits. • Turn off the power before installation. • Installation requires knowledge of electrical systems.
PAGE 2
Wall mount: Type 2: Wires from Pipe Ceiling mount: Type 2 : Wires from Conduit Step 1: Drill two holes and install the mounting base. Step 1: Tighten the bottom hole mounting and aim it with the upper hole. Step 2: Insert the wire conduit into the mounting base. Waterproof plaster Step 3: Connect the circuit wires to the fixture wires using wire nuts and electrical tape for a more secure connection. 45° Step 4: Tighten the screws, insert end caps, and adjust fixture mounting base.
PAGE 3
COMMERCIAL SERVICE Preparaciones para Instalacion INSTRUCTION MANUAL Quita el accesorio de la base de montaje. Artefacto LED a Prueba de Vapor Instrucciones de Instalacion Montaje al Techo: Tipo 1: Cables por el agujero central. ADVERTENCIAS: • Temperatura de funcionamiento: -22°F to 113°F (-30°C to 45°C). • Adecuado para lugares secos y húmedos. • Este dispositivo no puede utilizarse con salidas de emergencia. • Apague la corriente electrica antes de la instalación.
PAGE 4
Montaje a la pared: Tipo 2: Cabled del conducto. Montaje al Techo Tipo 2: Cables del Conducto. Paso 1: Taladre dos agujeros e instale la base de montaje. Paso 2: Inserte el conducto de alambre en la base de montaje. Paso 1: Apriete el agujero de abajo y orientalo hacia el agujero the arriba. 45° Agujeros impermeables y del conducto de yeso. Paso 3: Conecte los cables del circuito a los cables del artefacto usando conectores para cables y cinta aislante para una conexión más segura.
PAGE 5
COMMERCIAL SERVICE Préparation pour l’installation INSTRUCTION MANUAL Retirer le luminaire du socle de montage. Luminaire LED étanche à la vapeur Consignes d’installation Montage au plafond: Type 1: Câbles du trou centrr AVERTISSEMENTS: • Plage de température de fonctionnement: -30°C à 45°C (-22°F à 113°F). • Convient aux emplacement secs et humides. • Cet appareil n'est pas prévu pour une utilisation sur des issues de secours. • Couper le courant avant l’installation.
PAGE 6
Montage mural: Type 2: Câbles de tuyau Montage au plafond: Type 2: Câbles de conduite Étape 1: Percer deux trous et installer le socle de montage Étape 2: Insérer la conduite de câbles dans le socle de montage Étape 1: Serrer le socle de montage avec le trou inférieur et l’aligner avec le trou supérieur. Waterproof plaster Étape 3: Connecter les câbles du circuit aux câbles du luminaire à l’aide de cosses et d’un ruban isolant afin d’obtenir un raccordement plus sûr.