ETL-ES-Roundabout-WH12 Owner's Manual Manual del usuario Roundabout Model: GFP Series Please write model number here for future reference: / Por favor, incluya el número del modelo aquí para futura referencia: Net Weight: Peso Neto: LBS KGS
ETL-ES-Roundabout-WH12 2
ETL-ES-Roundabout-WH12 Safety tips OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR PERSONAL INJURY, MOUNT TO OUTLET BOX MARKED "ACCEPTABLE FOR FAN SUPPORT", AND USE THE OUTLET SCREWS PROVIDED WITH THE OUTLET BOX. MOST OUTLET BOXES COMMONLY USED FOR THE SUPPORT OF LIGHTING FIXTURES ARE NOT ACCEPTABLE FOR FAN SUPPORT AND MAY NEED TO BE REPLACED. CONSULT A QUALIFIED ELECTRICIAN IF IN DOUBT. 1.
ETL-ES-Roundabout-WH12 Consejos de seguridad HAGA LO SIGUIENTE: LEA Y GUARDE ESTAS INSTRUCCIONES 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. ADVERTENCIA: PARA REDUCIR EL RIESGO DE INCENDIO, DESCARGA ELÉCTRICA O LESIONES PERSONALES, MONTE EL VENTILADOR EN UNA CAJA DE EMBUTIR ROTULADA “ADECUADA PARA VENTILADORES”, Y UTILICE LOS TORNILLOS DE MONTAJE INCLUIDOS CON LA CAJA DE EMBUTIR.
ETL-ES-Roundabout-WH12 Features Características DOWNROD INSTALLATION VAULTED CEILING INSTALLATION instalación con varilla vertical INSTALACIÓN PARA CIELORRASOS ABOVEDADOS For normal ceilings May require a longer downrod (sold separately) Para cielorrasos normales Podría requerir una varilla vertical más larga (se vende por separado) 5
ETL-ES-Roundabout-WH12 pREPARING for installation Antes de la instalación 1 2 Unpack and inspect fan carefully to be certain all contents are included. Turn off power at fuse box to avoid possible electrical shock. Use metal outlet box suitable for fan support (must support 35 lbs). Before attaching fan to outlet box, ensure the outlet box is securely fastened by at least two points to a structural ceiling member (a loose box will cause the fan to wobble).
ETL-ES-Roundabout-WH12 Mounting bracket Installation Instalación con soporte de montaje 3 1 2 1 2 Remove the screws from the two mating holes (1) on the canopy. Loosen (do not remove) the screws in the mating slots (2) on the canopy. Rotate the mounting bracket and remove from the canopy. Quite los tornillos de los dos orificios coincidentes (1) del dosel. Afloje (no quite) los tornillos de las ranuras coincidentes (2) del dosel. Gire el soporte de montaje y sepárelo del dosel.
ETL-ES-Roundabout-WH12 Mounting bracket Installation Instalación con soporte de montaje MOUNTING OPTIONS OPCIONES DE MONTAJE 4 5 Choose a MOUNTING OPTION Elija una OPCIÓN DE MONTAJE NORMAL DOWNROD OPTION If installing downrod supplied with fan, proceed to page 9, step 6. OPCIÓN CON VARILLA VERTICAL PARA CIELORRASO NORMAL Si instala la varilla vertical incluida con el ventilador, proceda a la página 9, paso 6.
ETL-ES-Roundabout-WH12 NORMAL DOWNROD OPTION OPCIÓN CON VARILLA VERTICAL PARA CIELORRASO NORMAL 6 7 1 2 1 2 3 4 3 Insert downrod into downrod coupling. Make sure to align hole in downrod with the hole in downrod coupling. Install cross pin (1) through coupling and downrod. Insert keeper pin (2) into cross pin until it snaps into place. Tighten set screws (3) in coupling. Slide coupling cover (4) over the downrod coupling. PROCEEDTO PAGE 12, STEP 11.
ETL-ES-Roundabout-WH12 EXTENDED DOWNROD OPTION OPCIÓN CON VARILLA VERTICAL MÁS LARGA 8 9 3 2 1 1 2 Loosen downrod ball (1) from downrod (2) by removing set screw (3). Slide downrod ball (1) off of downrod and remove pin (2). Afloje la esfera de la varilla vertical (1) de la varilla vertical (2) quitando el tornillo (3). Deslice la esfera de la varilla vertical (1) hasta separarla de la varilla vertical y quite el pasador (2).
ETL-ES-Roundabout-WH12 EXTENDED DOWNROD OPTION OPCIÓN CON VARILLA VERTICAL MÁS LARGA 10 Re-install pin into extended downrod, and slide downrod ball up to the top of the downrod. Re-install set screw to secure ball to downrod. Note: Some extended downrods have a predrilled set-screw hole. If a pre-drilled hole is present in the extended downrod, tighten the set screw into the pre-drilled hole in the extended downrod.
ETL-ES-Roundabout-WH12 MOUNTING MONTAJE 11 12 Carefully lift fan assembly onto mounting bracket. Rotate fan until notch on downrod ball (1) engages the ridge on the mounting bracket (2). This will allow for hands free wiring. With bracket holding fan assembly, make electrical connections using the following step for wiring instructions. Levante con cuidado el conjunto del ventilador hasta el soporte de montaje.
ETL-ES-Roundabout-WH12 wiring OPTIONS OPCIÓN DE CABLEADO 13 PULL CHAIN WIRING OPTION 14 Follow diagram above to make wiring connections for fan pull chain control. WALL CONTROL WIRING OPTION Follow diagram above to make wiring connections for wall control operation. OPCIÓN DE CABLEADO PARA CONTROL DE PARED OPCIÓN DE CABLEADO PARA CADENILLA DE TIRO Siga las instrucciones del diagrama anterior para hacer las conexiones de cableado para el ventilador con control de pared.
ETL-ES-Roundabout-WH12 Secure To Ceiling Asegure el ventilador al cielorraso 15 For downrod fans, slide the canopy up to the mounting bracket. Para ventiladores con varilla vertical, deslice el dosel hacia arriba hasta el soporte de montaje. 3 2 1 The canopy has two mating slots (1) and two mating holes (2). Position both slots on canopy directly under and in line with two screws in the mounting bracket (3). Lift the canopy, allowing the two screws to slide into the mating slots.
ETL-ES-Roundabout-WH12 Blade Installation Instalación de las paletas 17 16 A. B. 1 2 3 Attach blade brackets to blades using the blade bracket screws (1), fabric washers (2) and nuts (3). Attach blade assembly to motor using the screws and washers provided. Tighten screws securely. Fije los soportes para paletas a las paletas con los tornillos (1), las arandelas de tela (2) y las tuercas (3). Fije el conjunto de las paletas al motor usando los tornillos y las arandelas incluidos.
ETL-ES-Roundabout-WH12 Light fixture installation Instalación del artefacto luminoso 18 19 1 2 Install light bulbs. Instale las bombillas de luz. Locate the indentations on the neck of the glass (2) and align with the protrusions from the light kit (1). Lift the glass up allowing the protrusions to engage the indentations on the glass, and twist the glass clockwise to lock into place.
ETL-ES-Roundabout-WH12 20 Assemble decorative fob and extension chains from hardware bag to fan pull chains by inserting end of chain into chain coupling. Confirm chains are held by lightly pulling both chains in coupling. Sujetar las cadenas largas de tiro con las piezas finales correspondientes, a las cadenas del ventilador, introduciendo el extremo de la cadena larga en la pieza de unión. Asegúrese de que las cadenas están bien sujetas, tirando ligeramente de ambas cadenas en la pieza de unión.
ETL-ES-Roundabout-WH12 OPERATION AND MAINTENANCE Operation Turn on the power and check operation of fan. The pull chain controls the fan speeds as follows: 1 pull - high; 2 pulls - medium; 3 pulls - low; 4 pulls - off. Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans and so on. The slide switch controls direction, forward or reverse. Warm weather/down position - (Forward) Fan turns counterclockwise direction.
ETL-ES-Roundabout-WH12 Troubleshooting guide TROUBLE 1. If fan does not start: If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults, please check this Trouble Shooting Chart. If a problem cannot be remedied, please consult with your authorized electrician and do not attempt any electrical repairs yourself. SUGGESTED REMEDY 1.
ETL-ES-Roundabout-WH12 Operación y mantenimiento Operación Encienda el ventilador y verifique su funcionamiento. La cadenilla de tiro controla las velocidades del ventilador de la siguiente manera: 1 jalón – rápida; 2 jalones - mediana; 3 jalones - lenta; 4 jalones - apagado. Las velocidades para clima cálido o frío dependen de factores como el tamaño de la habitación, la altura del ventilador, el número de ventiladores, etc.
ETL-ES-Roundabout-WH12 Si tiene dificultades para hacer funcionar su nuevo ventilador, podría ser a causa del armado, instalación o cableado incorrectos. En algunos estos errores de instalación podrían ser confundidos con defectos. Si experimenta alguna falla, consulte esta guía para solucionar Guía para solucionar problemas casos, problemas. Si no puede solucionar el problema, consulte a un electricista autorizado y no intente reparar conexiones eléctricas. PROBLEMA SOLUCIÓN SUGERIDA 1.
ETL-ES-Roundabout-WH12 22
ETL-ES-Roundabout-WH12 23
ETL-ES-Roundabout-WH12 Westinghouse Lighting Corporation 12401 McNulty Road Philadelphia, PA 19154 U.S.A. Westinghouse Lighting Corporation 12401 McNulty Road Philadelphia, PA 19154 U.S.A.
