Owners manual

ManualsBrandsWestin ManualsAutomotive21-534310 PRO TRAXX 5 in. Oval Nerf Step Bars Wheel-To-Wheel

Westin Automotive Products, Inc.

320 Covina Blvd

San Dimas, Ca. 91773

Thank You for choosing Westin products

For Additional installation assistance please call

Customer service (800) 793-7846

www.westinautomotive.com

P.N.: 75-1078-Rev. A

ECO #: W15-0038

DATE: 06/15/15

APPLICATION: 2009-2015 DODGE RAM 1500 CREW CAB W/ 5.5’ BED

2009-2015 DODGE RAM 1500 QUAD CAB W/ 6.5’ BED

APPLICATION PART # 21-534310 & 21-534315

ITEM QUANTITY DESCRIPTION TOOLS NEEDED

1 1 Driver Step Bar 3/8 Ratchet

2 1 Passenger Step Bar 17mm Socket

3 2 Mounting Bracket A 18mm Socket

4 2 Mounting Bracket B Allen key

5 1 Mounting Bracket C

3/8 Ratchet

Extension

6 1 Mounting Bracket D

7 6 M12 Stud Plate with M10 Nut Torque Wrench

8 6 M10 Riv-cert

9 12 M10 x 30mm Hex Head Cap Screw

10 12 M10 Split Lock Washer

11 12 M10 Flat Washer

12 6 M12 Hex Nut

13 6 M12 Split Lock Washer

14 6 M12 Flat Washer

15 4 M6 x 25mm Button Head Socket Cap Screw

16 4 M6 Flat Washer Big

17 4 M6 Flat Washer Small

18 4 M6 Split Lock Washer

19 4 M6 Hex Nut

20 16 M10 x 25mm Hex Button Head Cap Screw

21 12 M10 x 20mm Flat Washer

22 12 M10 Internal Toothed Lock Washer

23 6 Plastic Poly Retainer Squares

INSTALLATION INSTRUCTIONS

AUTOMOTIVE PRODUCTS, INC.

ANTI-SEIZE LUBRICANT MUST BE USED ON ALL STAINLESS STEEL FASTENERS TO PREVENT THREAD DAMAGE AND GALLING.

WHEEL-TO- WHEEL

Procedures

 Remove all contents from the box, verify if all the parts listed are present and free from damage.

 Carefully read and understand all instructions before attempting installation.

 Failure to identify damage prior to installation could lead to rejection of any claim.

Summary of content (4 pages)

PAGE 1
INSTALLATION INSTRUCTIONS WHEEL-TO- WHEEL AUTOMOTIVE PRODUCTS, INC. APPLICATION: 2009-2015 DODGE RAM 1500 CREW CAB W/ 5.5’ BED 2009-2015 DODGE RAM 1500 QUAD CAB W/ 6.
PAGE 2
A B Item 3 D Item 4 View 1 View 2 Item 8 Item 8 1. C Starting from either Passenger or Drivers side Rocker Panel, remove the tape that covers the slot, that is located above the 2 hexagon holes. (A total of 3 taped slots per side should be removed). Item 5 Item 6 Smaller step pad rear Item 2 Passenger step tube shown Tape Slot 2. Place Stud/nut plate onto the slotted hole (Item 7) as well as the hex riv-cert (Item 8) onto the hexagon hole.
PAGE 3
. 4. 5. 6. 7. 8. Bracket will be placed in the order for drivers side, shown on the picture to the right. In order to properly mount the riv-cert (Item 8) to the rocker panel, place the bracket as shown in the picture below tighten stud first then place washer with M10 bolt in the riv-cert and tighten. The riv-cert will expand and lock the riv-cert inside the rocker panel. Remove the M10 bolt and leave the top hardware in place loosely so that the stud can be moved.
PAGE 4
9. Install the running board, respectively to each side (short pad towards the rear), and secure to the brackets using (2) M10 Button Head bolts (item 20), (2) toothed lock washers (item 22) and (2) flat washers per bracket (item 21). 10. There will be two extra M10 Button head bolts that will need to go on the two riv-cert locations on the step bars. Those two threaded holes will not have a mounting bracket installed. 11. Adjust and tighten all M10 hardware to 30 lb.ft, M6 to 8 lb.ft.