User`s guide

ManualsBrandsWestern Telematic ManualsNetwork CardMPC Series MPC-16H-2

100

Table Of Contents

Figure 2.1: VMR Series - Front Panel (Model VMR-16HD20-1 Shown)
Figure 2.2: VMR Series - Back Panel (Model VMR-16HD20-1 Shown)
Figure 2.3: NPS Series - Front Panel (Model NPS-16HD20-1 Shown)
Figure 2.4: NPS Series - Back Panel (Model NPS-16HD20-1 Shown)
Figure 5.1: Boot Priority Example 1
Figure 5.2: Boot Priority Example 2
Figure 9.1: The Help Menu (Administrator Mode; Text Interface - VMR Shown)
Figure 14.1: Web Access Parameters (Text Interface Only)
Figure B.1: RS232 SetUp Port Interface
1. Introduction
2. Unit Description
- 2.1. VMR Series - Front Panel
- 2.2. VMR Series - Back Panel
- 2.3. NPS Series - Front Panel
- 2.4. NPS Series - Back Panel
- 2.5. Additional Button Functions
3. Getting Started
- 3.1. Installing the VMR Hardware
  - 3.1.1. Apply Power to the VMR or NPS
  - 3.1.2. Connect your PC to the VMR or NPS
- 3.2. Communicating with the VMR or NPS
4. Hardware Installation
- 4.1. Connecting the Power Supply Cables
  - 4.1.1. Installing the Power Supply Cable Keepers
  - 4.1.2. Connect the VMR or NPS to Your Power Supply
- 4.2. Connection to Switched Outlets
- 4.3. Serial SetUp Port Connection
  - 4.3.1. Connecting a Local PC
  - 4.3.2. Connecting an External Modem
- 4.4. Connecting the Network Cable
- 4.5. Rack Mounting
5. Basic Configuration
- 5.1. Communicating with the VMR or NPS Unit
- 5.2. Configuration Menus
- 5.3. Defining System Parameters
- 5.4. User Accounts
- 5.5. Managing User Accounts
- 5.6. The Plug Group Directory
- 5.7. Defining Plug Parameters
  - 5.7.1. The Boot Priority Parameter
    - 5.7.1.1. Example 1: Change Plug A3 to Priority 1
    - 5.7.1.2. Example 2: Change Plug A5 to Priority 2
- 5.8. Serial Port Configuration
- 5.9. Network Configuration
- 5.10. Save User Selected Parameters
  - 5.10.1. Restore Configuration
6. Reboot Options
- 6.1. Ping-No-Answer Reboot
- 6.2. Scheduled Reboot
7. Alarm Configuration
- 7.1. The Over Current Alarms (VMR Only)
  - 7.1.1. Over Current Alarms - Load Shedding and Auto Recovery
- 7.2. The Over Temperature Alarms
  - 7.2.1. Over Temperature Alarms - Load Shedding and Auto Recovery
- 7.3. The Circuit Breaker Open Alarm
- 7.4. The Lost Voltage (Line In) Alarm
- 7.5. The Ping-No-Answer Alarm
- 7.6. The Invalid Access Lockout Alarm
- 7.7. The Power Cycle Alarm
- 7.8. The Plug Current Alarm (VMR Only)
8. The Status Screens
- 8.1. Product Status
- 8.2. The Network Status Screen
- 8.3. The Plug Status Screen
- 8.4. The Plug Group Status Screen
- 8.5. The Current Metering Status Screen (VMR Only)
- 8.6. The Current History Screen (VMR Only)
- 8.7. The Power Range Status Screen (VMR Only)
- 8.8. The Power History Screen
9. Operation
- 9.1. Operation via the Web Browser Interface
  - 9.1.1. The Plug Control Screen - Web Browser Interface
  - 9.1.2. The Plug Group Control Screen - Web Browser Interface
- 9.2. Operation via the Text Interface
  - 9.2.1. Switching and Reboot Commands - Text Interface
  - 9.2.2. Applying Commands to Several Plugs - Text Interface
- 9.3. The Automated Mode
- 9.4. Manual Operation
- 9.5. Logging Out of Command Mode
10. SSH Encryption
11. Syslog Messages
- 11.1. Configuration
12. SNMP Traps
- 12.1. Configuration:
13. Operation via SNMP
- 13.1. VMR/NPS SNMP Agent
- 13.2. SNMPv3 Authentication and Encryption
- 13.3. Configuration via SNMP
- 13.4. Plug Control via SNMP
  - 13.4.1. Plug Status/Control
  - 13.4.2. Plug Group Status/Control
- 13.5. Viewing VMR/NPS Status via SNMP
  - 13.5.1. Plug Status
  - 13.5.2. Unit Environment Status
- 13.6. Sending Traps via SNMP
14. Setting Up SSL Encryption
- 14.1. Creating a Self Signed Certificate
- 14.2. Creating a Signed Certificate
- 14.3. Downloading the Server Private Key
15. Saving and Restoring Configuration Parameters
- 15.1. Sending Parameters to a File
- 15.2. Restoring Saved Parameters
- 15.3. Restoring Previously Saved Parameters
16. Upgrading VMR/NPS Firmware
- 16.1. Firmware Upgrade Utility (Recommended)
- 16.2. The Upgrade Firmware Function (Alternate Method)
17. Command Reference Guide
- 17.1. Command Conventions
- 17.2. Command Summary
- 17.3. Command Set
Appendix A. Specifications
Appendix B. Interface Descriptions
- B.1. SetUp Port (RS232)
Appendix C. Customer Service
Index

7-18

Alarm Configuration

• Address1,2,and3: These parameters are used to select which of the three email

addresses defined via the "Email Messages" menu (see Section 5.9.11) will receive

the email alarm notification messages generated by this alarm. The Address

parameters can be used to select one, or any combination of the addresses defined

via the Email Messages menu. (Default = All On.)

Note: If Email addresses have been previously specified, then the text under

the parameters will list the current, user defined email addresses.

• Subject: This parameter is used to define the text that will appear in the "Subject"

field for all email notification messages generated by this alarm. (Default = "Alarm:

Plug Current")

• PlugShedding: Allows individual plugs to be automatically switched Off or left

On when current consumption at the plug rises above the user-defined high Plug

Threshold value. (Default = Leave On.)

Note: In order to enable Plug Shedding, you must first set the high Plug

Threshold value for each desired plug.

• PlugGroupShedding: Allows user-defined Plug Groups to be automatically

switched Off or left On when current consumption by the Plug Group rises above

the user-defined high Plug Group Threshold high. (Default = Leave On.)

Note: In order to enable Plug Group Shedding, you must first set the high Plug

Group Threshold for each desired Plug Group.