User`s guide

ManualsBrandsWestern Telematic ManualsNetwork CardMPC Series MPC-16H-2

Table Of Contents

Figure 2.1: VMR Series - Front Panel (Model VMR-16HD20-1 Shown)
Figure 2.2: VMR Series - Back Panel (Model VMR-16HD20-1 Shown)
Figure 2.3: NPS Series - Front Panel (Model NPS-16HD20-1 Shown)
Figure 2.4: NPS Series - Back Panel (Model NPS-16HD20-1 Shown)
Figure 5.1: Boot Priority Example 1
Figure 5.2: Boot Priority Example 2
Figure 9.1: The Help Menu (Administrator Mode; Text Interface - VMR Shown)
Figure 14.1: Web Access Parameters (Text Interface Only)
Figure B.1: RS232 SetUp Port Interface
1. Introduction
2. Unit Description
- 2.1. VMR Series - Front Panel
- 2.2. VMR Series - Back Panel
- 2.3. NPS Series - Front Panel
- 2.4. NPS Series - Back Panel
- 2.5. Additional Button Functions
3. Getting Started
- 3.1. Installing the VMR Hardware
  - 3.1.1. Apply Power to the VMR or NPS
  - 3.1.2. Connect your PC to the VMR or NPS
- 3.2. Communicating with the VMR or NPS
4. Hardware Installation
- 4.1. Connecting the Power Supply Cables
  - 4.1.1. Installing the Power Supply Cable Keepers
  - 4.1.2. Connect the VMR or NPS to Your Power Supply
- 4.2. Connection to Switched Outlets
- 4.3. Serial SetUp Port Connection
  - 4.3.1. Connecting a Local PC
  - 4.3.2. Connecting an External Modem
- 4.4. Connecting the Network Cable
- 4.5. Rack Mounting
5. Basic Configuration
- 5.1. Communicating with the VMR or NPS Unit
- 5.2. Configuration Menus
- 5.3. Defining System Parameters
- 5.4. User Accounts
- 5.5. Managing User Accounts
- 5.6. The Plug Group Directory
- 5.7. Defining Plug Parameters
  - 5.7.1. The Boot Priority Parameter
    - 5.7.1.1. Example 1: Change Plug A3 to Priority 1
    - 5.7.1.2. Example 2: Change Plug A5 to Priority 2
- 5.8. Serial Port Configuration
- 5.9. Network Configuration
- 5.10. Save User Selected Parameters
  - 5.10.1. Restore Configuration
6. Reboot Options
- 6.1. Ping-No-Answer Reboot
- 6.2. Scheduled Reboot
7. Alarm Configuration
- 7.1. The Over Current Alarms (VMR Only)
  - 7.1.1. Over Current Alarms - Load Shedding and Auto Recovery
- 7.2. The Over Temperature Alarms
  - 7.2.1. Over Temperature Alarms - Load Shedding and Auto Recovery
- 7.3. The Circuit Breaker Open Alarm
- 7.4. The Lost Voltage (Line In) Alarm
- 7.5. The Ping-No-Answer Alarm
- 7.6. The Invalid Access Lockout Alarm
- 7.7. The Power Cycle Alarm
- 7.8. The Plug Current Alarm (VMR Only)
8. The Status Screens
- 8.1. Product Status
- 8.2. The Network Status Screen
- 8.3. The Plug Status Screen
- 8.4. The Plug Group Status Screen
- 8.5. The Current Metering Status Screen (VMR Only)
- 8.6. The Current History Screen (VMR Only)
- 8.7. The Power Range Status Screen (VMR Only)
- 8.8. The Power History Screen
9. Operation
- 9.1. Operation via the Web Browser Interface
  - 9.1.1. The Plug Control Screen - Web Browser Interface
  - 9.1.2. The Plug Group Control Screen - Web Browser Interface
- 9.2. Operation via the Text Interface
  - 9.2.1. Switching and Reboot Commands - Text Interface
  - 9.2.2. Applying Commands to Several Plugs - Text Interface
- 9.3. The Automated Mode
- 9.4. Manual Operation
- 9.5. Logging Out of Command Mode
10. SSH Encryption
11. Syslog Messages
- 11.1. Configuration
12. SNMP Traps
- 12.1. Configuration:
13. Operation via SNMP
- 13.1. VMR/NPS SNMP Agent
- 13.2. SNMPv3 Authentication and Encryption
- 13.3. Configuration via SNMP
- 13.4. Plug Control via SNMP
  - 13.4.1. Plug Status/Control
  - 13.4.2. Plug Group Status/Control
- 13.5. Viewing VMR/NPS Status via SNMP
  - 13.5.1. Plug Status
  - 13.5.2. Unit Environment Status
- 13.6. Sending Traps via SNMP
14. Setting Up SSL Encryption
- 14.1. Creating a Self Signed Certificate
- 14.2. Creating a Signed Certificate
- 14.3. Downloading the Server Private Key
15. Saving and Restoring Configuration Parameters
- 15.1. Sending Parameters to a File
- 15.2. Restoring Saved Parameters
- 15.3. Restoring Previously Saved Parameters
16. Upgrading VMR/NPS Firmware
- 16.1. Firmware Upgrade Utility (Recommended)
- 16.2. The Upgrade Firmware Function (Alternate Method)
17. Command Reference Guide
- 17.1. Command Conventions
- 17.2. Command Summary
- 17.3. Command Set
Appendix A. Specifications
Appendix B. Interface Descriptions
- B.1. SetUp Port (RS232)
Appendix C. Customer Service
Index

5-46

Basic Configuration

5.9.11. Email Messaging Parameters

The Email Messaging menu is used to define parameters for email messages that the

VMR/NPS can send to notify you when an alarm is triggered. To define email message

parameters, you must access the VMR/NPS Command Mode using a password that

permits access to Administrator Level commands.

The Email Messaging menu offers the following options:

• Enable: Enables/Disables the Email Messaging feature. When disabled, the VMR/

NPS will not be able to send email messages when an alarm is generated.

(Default = On.)

• SMTPServer: This prompt is used to define the address of your SMTP Email

server. (Default = undefined.)

• PortNumber: Selects the TCP/IP port number that will be used for email

connections. (Default = 25.)

• Domain: The domain name for your email server. (Default = undefined.)

Note: In order to use domain names, you must first define Domain Name

Server parameters as described in Section 5.9.5.

• UserName: The User Name that will be entered when logging into your email

server. (Default = undefined.)

• Password: The password that will be used when logging into your email server.

(Default = undefined.)

• AuthType: The Authentication type; the VMR/NPS allows you to select None,

Plain, Login, or CRAM-MD5 Authentication. (Default = Plain.)

• FromName: The name that will appear in the "From" field in email sent by the

VMR/NPS. (Default = undefined.)

• FromAddress: The email address that will appear in the "From" field in email sent

by the VMR/NPS. (Default = undefined.)

• ToAddress: The address(es) that will receive email messages generated by the

VMR/NPS. Note that up to three "To" addresses may be defined, and that when

Alarm Configuration parameters are selected as described in Section 7, you may

then designate one, two or all three of these addresses as recipients for email

messages that are generated by the alarms. (Default = undefined.)

• SendTestEmail: (Text Interface Only) Sends a test email, using the parameters

that are currently defined for the Email configuration menu.