User`s guide
Table Of Contents
- Figure 2.1: VMR Series - Front Panel (Model VMR-16HD20-1 Shown)
- Figure 2.2: VMR Series - Back Panel (Model VMR-16HD20-1 Shown)
- Figure 2.3: NPS Series - Front Panel (Model NPS-16HD20-1 Shown)
- Figure 2.4: NPS Series - Back Panel (Model NPS-16HD20-1 Shown)
- Figure 5.1: Boot Priority Example 1
- Figure 5.2: Boot Priority Example 2
- Figure 9.1: The Help Menu (Administrator Mode; Text Interface - VMR Shown)
- Figure 14.1: Web Access Parameters (Text Interface Only)
- Figure B.1: RS232 SetUp Port Interface
- 1. Introduction
- 2. Unit Description
- 3. Getting Started
- 4. Hardware Installation
- 5. Basic Configuration
- 5.1. Communicating with the VMR or NPS Unit
- 5.2. Configuration Menus
- 5.3. Defining System Parameters
- 5.4. User Accounts
- 5.5. Managing User Accounts
- 5.6. The Plug Group Directory
- 5.7. Defining Plug Parameters
- 5.8. Serial Port Configuration
- 5.9. Network Configuration
- 5.10. Save User Selected Parameters
- 6. Reboot Options
- 7. Alarm Configuration
- 8. The Status Screens
- 9. Operation
- 10. SSH Encryption
- 11. Syslog Messages
- 12. SNMP Traps
- 13. Operation via SNMP
- 14. Setting Up SSL Encryption
- 15. Saving and Restoring Configuration Parameters
- 16. Upgrading VMR/NPS Firmware
- 17. Command Reference Guide
- Appendix A. Specifications
- Appendix B. Interface Descriptions
- Appendix C. Customer Service
- Index
Index-9
Index
Switching Outlets On
Text Interface 9-4
Web Browser Interface 9-1
Switching Plugs Off
Text Interface 17-7
Web Browser Interface 9-2
Switching Plugs On
Text Interface 17-6
Web Browser Interface 9-2
Syslog 11-1
Audit Log and Alarm Log 5-11
Configuration 11-1
Syslog Address 5-32, 11-1
Syslog Messages 11-1
System Parameters 5-5 to 5-15, 17-9
Callback Security 5-6, 5-13 to 5-14
Front Panel Buttons 5-6
Invalid Access Lockout 5-5, 5-9
Log Configuration 5-6, 5-10 to 5-11
Management Utility 5-6
Modem Phone Number 5-6
Power Configuration 5-7
Real Time Clock 5-5, 5-7
Scripting Options 5-15
Site I.D. 5-5
Temperature Calibration 5-5
Temperature Format 5-5
User Directory 5-5
Voltage Calibration 5-14
System Reboot 17-10
T
TACACS
Access Level 5-42
Authentication Port 5-42
Configuration 5-42
Current/Power Metering 5-43
Default User Access 5-42
Enable 5-42
Fallback Local 5-42
Fallback Timer 5-42
Ping Test 5-43
Plug Access 5-43
Plug Group Access 5-43
Primary Address 5-42
Secondary Address 5-42
Secret Word 5-42
Service Access 5-43
Tech Support Apx-3
Telnet
Access 5-20
Max. per Source 5-31
Telnet Access 5-2, 5-31
Telnet Port 5-31
Temperature Calibration 5-5
Temperature Format 5-5
Temperature Log 5-6, 5-10
Test Menu 17-11
Test NTP Servers 5-8, 5-40, 5-43, 5-44
Text Interface 5-1 to 5-2, 9-3 to 9-6
Applying Commands to Several Plugs 9-5
Command Set 17-3 to 17-10
Initiating a Reboot Cycle 9-4
Set Plugs to Defaults 9-5
Switching Outlets Off 9-4
Switching Outlets On 9-4
Time 5-7
Scheduled Reboot 6-5
Time Zone 5-7
TLS/SSL Encryption 5-39
To Address
Email Parameters 5-46
Toggle All Plugs 2-5
Trademarks Apx-4
Trigger Enable
Invalid Access Lockout Alarm 7-13
Lost Voltage Alarm 7-10
Over Current Alarms 7-3
Over Temperature Alarms 7-6
Ping-No-Answer Alarm 7-11
Plug Current Alarm 7-16
Power Cycle Alarm 7-15
U
Unit Description 2-1 to 2-5, 2-3 to 2-5
Unit to Configure
Load Shedding 7-4
Unlock Port
Text Interface 17-8
Upgrade Firmware 17-11
Upgrading Firmware 16-1 to 16-3
Upload
CRT Server Key 14-4
Signed Certificate 14-4
User 5-17, 5-18, 17-2
User Accounts 5-17 to 5-23
Access Level 5-19
Access Levels 5-17
Adding 5-19
Command Access Levels 5-17
Current Monitoring 5-20
Deleting 5-21
Editing 5-21
Modifying 5-21
Password 5-19
Plug Access 5-18, 5-20
Plug Group Access 5-20
Port Access 5-20
Service Access 5-20
Username 5-19
Viewing 5-19
User Directory 5-5