Datasheet

US 7,099,934 B1
19
Command Completed Successfullyl”. The “X” in the mes
sage indicates the number of power manager ports modi?ed
by the command.
The “SET ENABLET
{STRTITEMPIMSTAICSTAILOAD} [Port NamelBoard
Name|Group|ALL]” command is used to enable an SNMP
trap. The SET ENABLET command takes tWo parameters.
The ?rst is the type of trap to be enabled. There are four
types of traps that are supported by the poWer manager,
STRT is a trap generated When the poWer manager is started
or resynchroniZed; TEMP is a trap generated When the
poWer manager temperature probe senses a temperature too;
MSTA is a trap generated When an IPM indicates an error
(Module STAus error); and, CSTA is a trap generated When
a poWer change occurs (Control STAus change).
LOAD is a trap generated When the load on an IPM is too.
If the ?rst parameter is not speci?ed the command does not
complete.
The second parameter is the Board Name for board Wide
traps (e.g., STRT and TEMP) and is the Port Name for IPM
speci?c traps (e.g., MSTA, CSTA and LOAD). If the Board
Name parameter is not speci?ed on the command line the
poWer manager prompts for the Boar Name With the
“Board:” prompt. If the Port Name parameter is not speci?ed
on the command line the poWer manager prompts for the
Port Name With the “Port Namez” prompt.
When the command completes the folloWing message is
displayed “Trap Enabled/disabled on X unit(s)/port(s) Com
mand Completed Successfullyl”. The “X” in the message
indicates the number of boards or ports for Which the
speci?ed trap is enabled or disabled by the command.
The “SET
DISABLET{STRTITEMPIMSTAICSTAILOAD} [Port
NamelBoard Name|Group|ALL]” command is used to dis
able an SNMP trap. The SET DISABLET command takes
tWo parameters. The ?rst is the type of trap to be disabled.
There are four types of traps that are supported by the poWer
manager. They are:
STRT is a trap generated When the poWer manager is
started or resynchroniZed.
TEMP is a trap generated When the poWer manager
temperature probe senses a temperature too.
MSTA is a trap generated When an IPM indicates an error
(Module STAus error).
CSTA is a trap generated When a poWer change occurs
(Control STAus change).
LOAD is a trap generated When the load on an IPM is too.
If the ?rst parameter is not speci?ed the command does not
complete.
The second parameter is the Board Name for board Wide
traps (e.g., STRT and TEMP) and is the Port Name for IPM
speci?c traps, e.g., MSTA, CSTA and LOAD. If the Board
Name parameter is not speci?ed on the command line the
poWer manager prompts for the Board Name With the
“Board:” prompt. If the Port Name parameter is not speci?ed
on the command line the poWer manager prompts for the
Port Name With the “Port Namez” prompt.
When the command completes the folloWing message is
displayed “Trap Enabled/disabled on X unit(s)/port(s) Com
mand Completed Successfullyl”. The “X” in the message
indicates the number of boards or ports for Which the
speci?ed trap is enabled or disabled by the command.
Regarding “LIST TRAP [Board Name|ALL]”, the LIST
TRAP command is used to list the current SNMP trap
settings on one or more boards in a chain of boards. The
LIST command is also used to list usernames and ports and
20
25
30
35
40
45
50
55
60
65
20
these functions are described in a usemame/password
administration section of this manual.
The LIST TRAP command takes a single parameter that
is the name of the board to be listed. If this parameter is
omitted, the poWer manager prompts for the board name
With the “Board:” prompt. If a user speci?es and absolute
board name (e.g., a period “.” folloWed by a letter), infor
mation on that speci?c board Will be displayed. If a mne
monic name is entered, the command Will display informa
tion on all boards With that board name With a “Press:
“N”)exet, “Q”)uit:” prompt betWeen board displays. The
folloWing is an example of the display that is returned by the
LIST TRAP command,
TRAP INFORMATION FOR UNIT: .A
poWer manager Start Up Trap: [X]
Temperature Error Trap: [X]
Temperature High Limit: 50 Deg C.
Tern erature LoW Limit: 1 De C.
.Al .A2 .A3 .A4
Control Status Trap [X] [X] [X] [X]
Module Status Trap [X] [ ] [ l [ l
Device Load Trap [X] [ ] [ l I l
Load High Limit 4 4 4 4
Load LoW Limit 1 l l 1
Press: “N”)ext, “Q”)uit: n
The display begins With a line that prints the absolute
board name for the board being displayed. Then a line is
displayed that indicates Whether the Start Up trap (STRT)
and the Temperature trap (TEMP) are active on this board.
An “X” betWeen the brackets means the trap is active. Even
if the Start Up trap is active, start up traps are generated on
the ?rst board in the chain of boards.
The next line shoWs the current Temperature trap limits
for this board. FolloWing the temperature limits, is a four
column matrix that shoWs Which traps are enabled for Which
ports on this board. An “X” betWeen the brackets corre
sponding to the trap and the port indicates the trap is active.
Only the absolute port names are displayed. FolloWing the
enabled/disabled display for the traps, is a display of the
current device load high and loW limits for each of the four
ports on this board. Finally, a prompt to continue With the
next board or quit is displayed. When the command is
complete a “Port List Complete” message is printed.
Usemame/passWord and Serial Port Name administration
commands are available When logged in With the adminis
trative usemame (e.g., admn). These commands are used to
add/delete users, to alloW/disalloW access to poWer manager
IPMs for usernames and to vieW the current usernames and
their associated IPM access. They are also used to assign
names to the various serial ports that can be accessed via the
CONNECT command.
Regarding “ADD {USERIPORTISNAME}
[Usemamelserial Port ID] [Port NamelSerial Port Name]”,
the ADD command is used to add usernames to the system,
to add Serial Port Names, and to add port access to a
usemame. The ADD command takes one required parameter
and up to tWo optional parameters.
The ?rst parameter is required and indicates Whether a
usemame is to be added (ADD USER) or Whether port
access is to be granted to a user (ADD PORT), or Whether
a Serial Port Name is to be added (ADD SNAME).
The ADD USER command is used to add a neW usemame
to the system. The command can be entered With a single