6641-2201 Viper 108 and 408 Managed 8-port Ethernet Switch www.westermo.
Legal information The contents of this document are provided “as is”. Except as required by applicable law, no warranties of any kind, either express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are made in relation to the accuracy and reliability or contents of this document. Westermo reserves the right to revise this document or withdraw it at any time without prior notice.
Safety ! Before installation: Read this manual completely and gather all information on the unit. Make sure that you understand it fully. Check that your application does not exceed the safe operating specifications for this unit. This unit should only be installed by qualified personnel. This unit should be built-in to an apparatus cabinet, or similar, where access is restricted to service personnel only. The power supply wiring must be sufficiently fused (e.g. Littlefuse 0461 1.
Agency approvals and standards compliance Type EMC Approval / Compliance EN 61000-6-1, Immunity residential environments EN 61000-6-2, Immunity industrial environments EN 55024, Immunity IT equipment EN 61000-6-3, Emission residential environments EN 61000-6-4, Emission industrial environments EN 50121-3-2, Railway applications - EMC: Rolling stock – Apparatus FCC part 15 Class B EN 50121-4, Railway signalling and telecommunications apparatus IEC 62236-4, Railway signalling and telecommunications apparatus
Declaration of Conformity Westermo Teleindustri AB Declaration of conformity The manufacturer Westermo Teleindustri AB SE-640 40 Stora Sundby, Sweden Herewith declares that the product(s) Type of product Unmanaged Ethernet switch Managed Ethernet switch Model Viper-008 Viper-408 Viper-408 E-mark Art no 3641-0340 3641-0360 3641-6360 is in conformity with the following EC directive(s).
Type tests and environmental conditions Phenomena ESD Test EN 61000-4-2 RF field AM modulated IEC 61000-4-3 Fast transient EN 61000-4-4 Surge EN 61000-4-5 RF conducted EN 61000-4-6 Description Enclosure contact Enclosure air Enclosure Ethernet ports Power port Earth port Fault port Ethernet ports Power port Ethernet ports Power port Power frequency magnetic field Pulse magnetic field Voltage dips and interruption EN 61000-4-8 Enclosure EN 61000-4-9 EN 50155 Enclosure DC power ports Radiated
Phenomena Shock, half sine pulses Test IEC 60068-2-27, Cat. 1 class B (EN 61373) Description Operating Test levels Shock, sawtooth IEC 60068-2-27, Cat. 1 class B (IEEE1478-2001) Operating Vertical: 100 m/s2 Transverse: 100 m/s2 Longitudinal: 100 m/s2 11 ms, 3 x 6 shocks Enclosure Dimension W x H x D Weight Degree of protection UL 94 Nickel coated zinc IEC 529 Enclosure Flammability class V-1 175 x 100 x 50 mm 0.
Description Functional description Viper is a range of switches consisting of two different function levels developed for rail and industrial applications. To meet the environmental requirements from rail and harsh industrial applications the switch has rugged M12 Ethernet connectors and full metal housing. The switch fullfill IP 65 degree of protection when all ports are protected/ connected else IP 40.
Interface specifications Power and fault relay port PWR Rated voltage 24 to 110 VDC Operating voltage 24 to 110 VDC ±40% Rated current Rated frequency 40 mA @ 110 VDC 140 mA @ 24 VDC DC Inrush current, I2t Max 0.02 A2s @ 24 – 110 VDC Startup current * 7 Apeak @ 24 – 110 VDC Polarity Reverse polarity protected Redundant power input No Isolation to Connections X1 – X8 and to ground, 1500 VAC.
Fault Contact The Viper switch is equipped with a potential free normally closed fault contact. The fault contact is a solid state component (relay) that requires power to work and it is transient protected. Additionally, the fault contact is opened when any of the following conditions is met: • No voltage on the power supply pin, a voltage level outside the legal voltage range or current limitation on the voltage source is applied on the power input. • Link alarm i.e.
Ethernet TX port X1 to X8 Electrical specification IEEE std 802.3.
Location of Interface ports, LED's LED indicators LED Status Description PWR GREEN Unit indicates no fault RED Unit indicated fault FLASH Connected to IP Configuration tool OFF FRNT is not enabled or not supported GREEN RED FRNT is running and the switch is configured as member switch in the ring.
Configuration The units can easily be configured via the onboard Web based configuration tool. Local IP addresses can also be configured by using the Westermo IP Configuration tool, from the IP Configuration tool it is then possible to browse into the unit for further configuration. IP Address When delivered, the default IP address of the Viper is 192.168.2.200. Default gateway 192.168.2.
By clicking the “Scan for Devices” button the IP Configuration tool will detect the switches/routers in the network. The software will list all Westermo managed switches or routers connected to the network. Information as in the figure 1 will appear for each detected unit connected to the same network as your PC. IP configuration If you only want to change the IP address and the subnet mask, this can be done within the IP config tool.
Westermo - location - Provided by Westermo UK http://192.168.2.200/conf/p.cgi File Edit View Favorites Tools Westermo - location Help Log in via Web Google You will be prompted with a Login screen where the default settings for Username and Password are: Home Feeds (J) Print Page Tools Username: admin Password: westermo Login Username: Password: Login Figure 5 Done Internet The unit can be easily configured via the on-board Web based configuration tool.
Mounting There are four 6 mm bore holes intended for mounting the unit. The unit can be mounted vertical or horizontal. The unit is wall mounted. X5 X1 FRNT X2 SERVICE X6 X7 X3 ST1 ST2 PWR X4 X8 Removal Disconnect all cables and unscrew the unit from the wall. Cooling This unit uses convection cooling. Avoid obstructing the airflow around the unit. Spacing is recommended for the use of unit in full operating temperature range and service life.
Factory Reset The factory reset option restores the switch to its original factory condition. The switch will be restored using the following settings. • IP address 192.168.2.200 • Subnet mask 255.255.255.0 • Gateway 192.168.2.1 • All Ethernet ports are enabled and set to Auto Negotiate • All applications are disabled • Password reset to westermo To perform a Factory Reset follow the procedure below. Read all steps before starting.
Dimensions Measurements are stated in millimeters.
Westermo • SE-640 40 Stora Sundby, Sweden Tel +46 16 42 80 00 Fax +46 16 42 80 01 E-mail: info@westermo.com www.westermo.com United Kingdom Westermo Data Communications Talisman Business Centre Duncan Road, Park Gate, Southampton. SO31 7GA Tel: +44 (0) 1489 580 585 • Fax: +44 (0) 1489 580 586 sales@westermo.co.uk • www.westermo.co.uk Germany Westermo Data Communications Goethe Strasse 67 DE-68753 Waghäusel Tel: +49 (0) 7254 95400-0 • Fax: +49 (0) 7254-95400-9 info@westermo.de • www.westermo.
