6641-2252 Viper-12-PoE s e r i e s PoE X1 X5 X9 X6 X10 X7 X11 X8 X12 ON USB X2 RSTP FRNT X3 CON DC X4 12-port Ethernet M12 switch with Power over Ethernet www.westermo.
License Information This device contains public available software which is under the GPL license. For more information see legal.pdf included with all firmware releases. This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. http://www.openssl.org Legal information The contents of this document are provided “as is”.
Safety ! Before installation: Read this manual completely and gather all information on the unit. Make sure that you understand it fully. Check that your application does not exceed the safe operating specifications for this unit. This unit should only be installed by qualified personnel. This unit should be built-in to an apparatus cabinet, or similar, where access is restricted to service personnel only.
Agency approvals and standards compliance Type Approval / Compliance EMC EN 61000-6-1, Immunity residential environments EN 61000-6-2, Immunity industrial environments EN 61000-6-4, Emission industrial environments EN 55022, Emission IT equipment EN 55024, Immunity IT equipment EN 50121-3-2, Railway applications – Rolling stock – apparatus EN 50121-4 / IEC 62236-4, Railway signaling and telecommunications apparatus FCC part 15 Class A Safety EN 60950-1, IT equipment Environmental EN 61373 Railway app
Declaration of Conformity Westermo Teleindustri AB Declaration of conformity The manufacturer Westermo Teleindustri AB SE-640 40 Stora Sundby, Sweden Herewith declares that the product(s) Type of product Model Art no 12-port managed Ethernet M12 PoE Viper-112-P8, -212-P8 3641-0580, -0590 Switch 12-port managed Gig Ethernet M12 PoE Viper-112-T3G-P8, -212-T3G-P8 3641-0570, -0595 Switch is in conformity with the following EC directive(s).
Type tests and environmental conditions Environmental phenomena ESD Basic standard Description EN 61000-4-2 Enclosure Fast transients EN 61000-4-4 Surge EN 61000-4-5 Power port Ethernet ports Earth port Power port Power frequency magnetic field Pulsed magnetic field Radiated RF immunity EN 61000-4-8 EN 61000-4-9 EN 61000-4-3 Ethernet ports Enclosure Enclosure Enclosure Conducted RF immunity EN 61000-4-6 Radiated RF emission Conducted RF emission EN 55022 FCC Part 15 EN 55022 Dielectric strengt
Description Designed for harsh industrial environments The Viper-12-PoE series is a series of managed rugged Ethernet switches with Power over Ethernet, designed for applications with severe operating conditions and extreme environments.
Interface specifications DC, Power port Rated voltage Operating voltage Rated current Rated frequency Inrush current, I²t Startup current* Polarity Redundant power input Isolation to Connection Connector size 48 to 110 VDC 33.6 to 143 VDC (28.8 to 154 VDC for 100 ms) Viper-x12-P8: Max 1.7 A @ 48V Max 0.8 A @ 110 V Viper-x12-T3G-P8: Max 1.8 A @ 48V Max. 0.8 A @ 110 V DC 21 mA²s @ 48 V 68 mA²s @ 110 V Max 1.8 A @ 48 V Max 0.
X1-X3, X5-X7, X9-X10, PoE ports (additional data) Electrical specification IEEE std 802.3af, 2003 edition, IEEE std 802.3at, 2009 edition Transmission range Up to 100 m with CAT5e cable or better Output voltage 54 VDC, ±5% Output power* Max 30.8 W on one port Max 61.6 W in total on all ports * Note! As delivered by Power Sourcing Equipment, i e the Viper-12-PoE switch. Power available at Powered Device is depending on cable resistance.
Location of interface ports and LED’s Viper-112-P8 and Viper-212-P8 LED indicators (for details see page 13) Ethernet connection TX (X1 – X12) (for details see page 8 and 11) PoE X1 X5 X9 ON USB RSTP FRNT X2 X6 X10 X3 X7 X11 X4 X8 X12 CON DC Earth connection Power connection for details see page 8 and 11) Location of interface ports and LED’s Viper-112-T3G-P8 and Viper-212-T3G-P8 LED indicators (for details see page 13) Earth connection 10 Ethernet connection TX (X1 – X12) (for details
Viper-112-P8 / Viper-212-P8 Viper-112-T3G-P8 / Viper-212-T3G-P8 Ethernet connection (X1-X12 on Viper-x12-P8, X1-X3, X5-X7, X9-X11 on Viper-x12-T3G-P8) Pin number No 1 No 2 No 3 No 4 Housing Signal TD+ RX+ TX– RD– Shield Power connection Pin number No 1 No 2 No 3 No 4 Signal +DC1 +DC2 -COM -COM 2 1 3 4 Viper-12-PoE supports redundant power connection. The positive inputs are +DC1 and +DC2, the negative input for both supplies are –COM.
Connection to console port The console port can be used to connect to the CLI (Command Line Interface). The following steps needs to be taken 1. Connect the serial diagnostic cable (use Westermo cable 1211-2215 to the console port). 2. Connect cable to your computer serial port. 3. Use a terminal emulator and connect with correct speed and format (115200, 8N1) to the assigned port. For more information about the CLI, see the WeOS management guide.
LED Indicators LED ON Status OFF GREEN RED BLINK DC FRNT OFF GREEN RED OFF GREEN RED BLINK RSTP OFF GREEN BLINK X1 to X12 OFF GREEN GREEN FLASH YELLOW PoE OFF GREEN 6641-2252 Description Unit has no power. All OK, no alarm condition. Alarm condition, or until unit has started up. (Alarm conditions are configurable, see ''WeOS Management Guide''). Location indicator ("Here I am!"). Activated when connected to IPConfig Tool, or when configuring the unit via Web or CLI. Unit has no power.
Wall mounting There are four 6 mm bore holes intended for mounting the unit. The unit can be mounted vertical or horizontal. Use four M5 screws with 12 mm washer on a flat and stable surface. PoE X1 X5 X9 ON USB RSTP FRNT X2 X6 X10 X3 X7 X11 X4 X8 X12 CON DC Connection of cables Recommended tightening torque for the M12 connectors: 0.6 Nm Removal Disconnect all cables and unscrew the unit from the wall. Time For Replacement < 15 minutes Cooling This unit uses convection cooling.
Getting Started This product runs Westermo Operating System (WeOS) which provides several management tools that can be used for configuration of the unit. • IPConfig tool This is a custom Westermo tool used for discovery of attached Westermo units. Note! Version of IP Config tool must be 10.4.0 or higher. • Web Configuration of the unit using the web browser. • CLI Configuration of the unit via the Command Line Interface.
Referring documents Type Management Guide Description Westermo OS management guide Document number 6101-3201 Factory reset It is possible to set the unit to factory default settings by using two standard Ethernet M12 cables. 1. Power off the switch and disconnect all Ethernet cables. 2. Connect one Ethernet cable between Ethernet ports X1 and X6, and the other between Ethernet ports X2 and X5. The ports need to be connected directly by an Ethernet cable, i.e., not via a hub or switch.
Dimensions Measurements are stated in millimeters.
Westermo • SE-640 40 Stora Sundby, Sweden Tel +46 16 42 80 00 Fax +46 16 42 80 01 E-mail: info@westermo.com www.westermo.com United Kingdom Westermo Data Communications Talisman Business Centre Duncan Road, Park Gate, Southampton. SO31 7GA Tel: +44 (0) 1489 580 585 • Fax: +44 (0) 1489 580 586 sales@westermo.co.uk • www.westermo.co.uk Germany Westermo Data Communications Goethe Strasse 67 DE-68753 Waghäusel Tel: +49 (0) 7254 95400-0 • Fax: +49 (0) 7254-95400-9 info@westermo.de • www.westermo.
