DR-250 WARNING DSL2/2+ Router www.westermo.
Legal information The contents of this document are provided “as is”. Except as required by applicable law, no warranties of any kind, either express or implied, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose, are made in relation to the accuracy and reliability or contents of this document. Westermo reserves the right to revise this document or withdraw it at any time without prior notice.
Safety ! Before using this unit: Read this manual completely and gather all information on the unit. Make sure that you understand it fully. Check that your application does not exceed the safe operating specifications for this unit. Hazardous voltages may occur within this unit when connected to a power supply. Prevent access to hazardous voltages by disconnecting the unit from its power supply.
General Remember to follow any special regulations and warnings in force in any area and never use the unit whenever it’s forbidden to use it. Do not use the unit when it may cause interference or danger. A wireless device exposed to interference above specified limits could result in deteriorated performance. Hospitals or other Medical environment Do not use the unit in a medical environment such as health care facilities. Follow any regulations or rules that instruct you to not use the unit.
For Vehicles equipped with an airbag An air bag inflates with great force. DO NOT place objects, including either installed or portable wireless equipment, in the area over the air bag or in the air bag deployment area. If in-vehicle wireless equipment is improperly installed and the air bag inflates, serious injury could result. Blasting areas Do not use the unit where blasting is in progress or in “blasting areas”. Observe restrictions and follow any regulation or rules.
Agency approvals and standards compliance 6 Type Approval / Compliance EMC EN301489-07: v1.2.1 (2002-08) EN55022 1998 EN55024: 1998+A1:2001 Safety IEC60950-1: 2005 Second Edition EN60950-1:2006 RF spectrum EN301511: v9.0.
Declaration of Conformity Westermo Teleindustri AB Declaration of conformity The manufacturer Westermo Teleindustri AB SE-640 40 Stora Sundby, Sweden Herewith declares that the product(s) Type of product Model Art no ADSL 2/ 2+ Router DR-250 3622-0010 is in conformity with the following EC directive(s). No Short name 1999/5/EC radio and telecommunications terminal equipment (R&TTE) References of standards applied for this EC declaration of conformity.
Type tests and environmental conditions Environmental Temperature Operating –20 to +55°C Packaging 8 Enclosure Pressed steel Dimension W x H x D 236 x 146 x 29 mm Weight 0.8 kg – 1.
Description The DR-250 Is based on the very latest ADSL2/2+ platform, supporting the fastest broadband speeds available. ADSL2 offers considerable performance benefits over standard ADSL, including improved range and data rate. The DR-250 has an integral four port Ethernet switch and a 25 pin RS-232 serial interface for local connectivity. Devices that support serial protocols such as Modbus RTU, DF1, DNP3, IEC870 etc can be easily connected to the DR-250 via the serial port.
Interface specifications Power Rated voltage Rated current Rated frequency 10 – 28 VDC 1500 mA @ 12 VDC DC RS-232 Electrical specification Data rate Data format Transmission range Connection RS-232 V.24 300 bit/s – 115.2 kbit/s 7 or 8 data bits, Odd, even or no parity, 1 or 2 stop bits 2m 25-pin D-sub female (DCE) Ethernet Electrical specification IEEE std 802.3.
Connections SIM Card Sockets The two sockets at the left side of the front panel are for the GSM SIM card(s) that you will receive from your service providers. Details of how to insert these correctly are given on page 13. USB Host Connectors* LED Indicators (for details see next page) Antenna interface RS-232 interface** Ethernet interface Antenna interface Ethernet interface Power interface cord * The USB host connectors may be used to connect compatible USB 2.
LED Indicators LED PWR LAN 0, 1, 2, 3 DTE DSL W-WAN Signal ISDN PSTN Status ON OFF ON OFF Flash ON OFF Description In service Out of service Network connection on LAN port No connection on LAN port Transmit or recive data on LAN port Terminal connected to the serial port and the DTR signal is on No connection on serial port Data is transmitted or received on the serial port Flash Data is transmitted or received on the serial port ON RED No DSL is detected FLASH RED DSL training ON GREEN DSL active FL
Installation Mounting / Removal The router should be positioned on a smooth, level surface making sure that there is adequate ventilation. Do not expose the router to extremes of heat or cold, strong magnetic fields or liquids. If the GSM option is fitted it is important to remember that these products are wireless devices just like a mobile phone, so they will only operate reliably over the GSM network if there is a good signal.
Step 4 – Connecting the serial cable For connection to a serial terminal device, connect the 25-way D plug on the serial cable provided to the SERIAL connector on the rear of the unit. Connect the other end of the cable (9-way D socket) to the terminal. If the serial connector on the terminal is not a 9-way D plug, you will need a suitable adapter. Step 5 – Connecting the ADSL cable Plug one end of the supplied cable, or a suitable alternative, into the RJ12 socket labelled ADSL.
Getting started IP Address The default IP address of the DR-250 when delivered is 192.168.0.99. IP address configuration The IP address is configurable by the Web tool and/or by using a terminal program. Below is an description of how to configure the IP address by using a terminal program. 1. If the address is known, connect to the unit from a Web browser with the address of the DR-250. If the address is unknown, connect the serial RS-232 interface to a terminal program with settings: Data rate: 115.
Configuration by Web Tool The DR-250 includes an easy-to-use Web configuration tool. The Web tool is very intuitive and includes useful help information for the configurable parameters. Connect and login to the DR-250 on the default IP address and with default username and password combination (or your customized if configured) using a standard Web browser. Basic ADSL setup The following must be done to get basic ADSL connectivity. There are two different ways that are used to get a ADSL connection.
Basic Ethernet configuration Basic IP Address • Static IP To change the default IP-address 192.168.0.99 and subnet mask to something else. Basic IP Address • DHCP Minimum assigned IP address: eg 192.168.0.2 IP address range: eg 20 (highest address will then be 192.168.0.22) DNS server address: Address of router (192.168.0.99 default setting) Gateway address: Address of router (192.168.0.99 default setting) Mask: 255.255.255.0 All settings above must be saved to one of the two profiles and then restarted.
Westermo Teleindustri AB • SE-640 40 Stora Sundby, Sweden Phone +46 16 42 80 00 Fax +46 16 42 80 01 E-mail: info@westermo.se Westermo Web site: www.westermo.com Westermo Data Communications AB Svalgången 1 SE-724 81 Västerås Phone: +46 (0)21 548 08 00 • Fax: +46 (0)21 35 18 50 info.sverige@westermo.se Westermo Data Communications Ltd Talisman Business Centre • Duncan Road Park Gate, Southampton • SO31 7GA Phone: +44(0)1489 580-585 • Fax.:+44(0)1489 580586 E-Mail: sales@westermo.co.
