Installation manual
ENGINE 
ADJUSTMENTS 
NOTE: 
WESTERBEKE 
recommends 
that 
the 
following 
engine 
adjust-
ments 
be 
peTjonned 
by 
a 
competent 
engine 
T(lechanic. 
The 
infonnation 
below 
is 
provided 
to 
assist 
the 
mechanic. 
TESTING 
OIL 
PRESSURE 
To 
test 
oil 
pressure, 
remove 
the 
hex 
head 
plug 
from 
the oil 
gallery 
and 
install 
a 
mechanical 
oil 
pressure 
gauge 
in its 
place. 
After 
warming 
up 
the 
engine, 
read the oil pressure 
gauge. 
OIL 
PRESSURE 
BETWEEN 
35 
AND 
55 
PSI 
NOTE: 
A 
newly 
started, 
cold 
engine 
may 
have 
an 
oil 
pressure 
reading 
up 
to 
70 
or 
80 
psi. 
A 
wanned 
engine 
can 
have 
an 
oil 
pressure 
reading 
as 
low 
as 
30 
psi. 
Oil 
pressure 
will 
vary 
del,eruljng 
upon 
the 
load 
placed 
on 
the 
engine. 
OIL 
PRESSURE 
GAUGE 
WITH 
ADAPTER 
TESTING 
DlL 
PRESSURE 
THIS 
MECHANICAL 
TEST' 
GA1JGECA~ 
INSTALLED 
WHERE 
THE 
OIL 
HU~H~' 
I 
cH; 
THE 
ENGINE 
BLOCK 
OR. 
IN 
PLACE 
OF 
THE 
OIL 
PRESSURE 
SENDER. 
A 
CAUTION: 
Be 
sure 
to 
stop 
the 
engine 
bef~re 
checking 
the 
engine. 
Keep 
your 
hands 
away 
from 
rotating 
parts 
such 
as 
the 
cooling 
fan, 
vĀ·belt, 
pulleys, 
and 
flywheel. 
Keep 
long 
hair 
away 
from 
rotating 
parts 
and 
do 
not 
wear 
music 
earphones. 
LOW 
OIL 
PRESSURE 
A 
gradual 
loss 
of 
oil 
pressure 
usually 
indicates 
a 
worn 
bear-
ings. 
A 
rapid 
loss 
of 
oil 
pressure 
indicates a 
specific 
bearing 
failure. 
For 
additional 
information 
on 
low 
oil 
pressure 
,ead-
ings, 
see 
the 
ENGINE 
TROUBLESHOOTING 
chart. 
OIL 
PRESSURE 
RELIEF 
VALVE 
The 
all 
pressuterelief valve 
is 
located. 
in 
the 
front 
gear case 
cover just 
below 
the oil 
pressure 
senders 
location. 
It 
is 
held 
in place 
by 
a 
22mm 
hexhead 
plug. 
This 
valve's cracking 
pressure 
is 
approximately 
45 
psi 
and 
operates 
to 
maintain the 
pressure 
in 
the 
engine's 
lubricating 
system. 
OIL 
PRESSURE 
SWITCH 
There 
is 
an 
oil 
pressure 
switch 
connected 
into 
the 
engine's 
oil gallery 
to 
monitor 
the 
engine 
oil 
pressure 
and 
to 
sonnd 
the panel 
alarm 
buzzer. 
should 
a 
low 
oil 
pressure 
issue occur 
(5-10 
psi). 
The engine alarm 
buzzer 
in 
such 
cases 
will sound 
continuously. 
NOTE: 
This 
alann 
will 
sound 
when 
starting 
the 
engine 
and 
will 
shut 
off 
once 
il-ie 
oil 
pressure 
exceeds 
5-10 
psi. 
Engines & Generators 
40 










