X12LM DIGITAL WIRELESS INTERCOM
Table of Contents I Contents I Caution ---------------------------------------------02 Certificate -------------------------------------------03 Introduction Product Image ---------------------------------- 04 Function Power ----------------------------------------Volume Setting ------------------------------Channel Setting ------------------------------Mic Volume Level --------------------------Mic Mute ----------------------------------How to reset case of malfunction ----------How to charge ----------
Caution X12LM operates in the license-free 900MHz ISM band. X12LM subject to the Rules and Regulations of the FCC. This device complies with part 15 of the FCC rules. Operation is subject to th e following two conditions: (1)This device may not cause harmful interference, and (2)this device must accept any interference received, including interferenc e that may cause undesired operation.
Caution * Do not put sharp, hard materials into the connector hole when using this product. * Do not put apart or repair X12LM yourself. * Do not leave X12LM in a vehicle in hot or cold weather. * Leaving X12LM in a closed area for a long period of time may result in deformation or malfunction of this product. * For charging use only the provided charger & cable. Using a third party charger may cause explosion, fire or malfunction. * Stop using X12LM immediately if you smell something like smoke from this.
Introduction Product Image FRONT Power/Select Channel Up Volume Up Mute Channel Down Volume Down TOP & SIDE & BOTTOM Charging LED Link LED Mic Speaker Charging port Mount -04-
Function 1. Power Power on, off with PWR button 2 sec Note If device is left in standby mode for half hour, it is automatically turned off for power-saving.
Function 2. Volume Setting Volume level ranges from 0 to 8. Note Volume 0 means no audio volume 3. Channel Setting Devices should be set to same channel number for communication. If there are multiple communication groups in the same channel nearby, set channel number different from other groups to avoid potential interference.
Function 4. Mic Level You can adjust the Microphone Volume level. With this function your voice transmission is clearer if you set it right, depending on your voice level. STEP 1 Press&hold button and Volume Up Button to control mic level + STEP 2 Choose between “0” and “8” (The higher number you choose, the higher microphone volume it transmits) “Mic Level” 0 means microphone is mute 5. Mic Mute User 1~12 can mute microphone by pressing ‘M’ button shortly. Users only listen if they mute microphone.
Function 6. How to reset in case of malfunction + + Press these buttons together at the same time. Then the device goes off. Note Be careful not to press these buttons together during normal operation. 7. How to charge While on charge, red light on the lower display lights up and the green light becomes dimmer once the device is fully charged. Note Please use only the provided charging adapter or use 5V / 2A adapter or higher than that.
FAQ Following is the list of frequent questions and answers. 1 I can’t communicate with other devices. - Check if your device is paired with Master Device. - In your group, check if Master Device exists. 2 I cannot join a group communication. - Check if other users are connected on the display. - Check if there is a Master Device in the group. - You might be too far from Master Device to get the signal from it. . 3 I cannot turn on the device.
Specification & Caution Frequency 902MHz~928MHz Transmission Distance 1Km (Line of Sight) Battery Lifetime 10Hour Battery Rechargeable Li-ion 3.7V Battery Transmission Output 250mW Weight 380g Size Width(w) : 105mm Height(h) : 105(117.1)mm Thickness(t) : 40.7(49.3)mm Working Temperature -10/+50℃ Modulation System FSK Transmission Method TDMA ※ The function may change without notice for product improvement purpose.
FCC Information This device complies with part 15 of the FCC Results. Operation is subject to the following two conditions : (1) This Device may not cause harmful interface, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for CLASS B digital device, pursuant to Part 15 of FCC Rules.
