Instruction Manual
Wiring
Synchronization of several programmers is by slave block preset coupling. The slave blocks are forced to the same time
or to the same segment number via time or segment preset by the master.
To facilitate operation of the coupled blocks, the programmer has a SlavNo input and a Bl-no output. These are used
by the slave block for transfer of the block number to the following block (see Fig 49). The block the Blo-no output of
which is not connected (block 100 in this example) should operate as master. Its Tnetto or SegNo output is wired to the
PSet input of further blocks.
By linking the blocks (
Bl-no > SlavNo), a programmer with coupled blocks is created. From the master
block operating page, access to the data (incl. parameters) relevant for the slave for display or adjustment is pos
-
sible easily.
Operation of a programmer with several blocks
Calling up a master block operating page via the operating page menu (page survey):
When selecting the operating page of a master programmer via the operating page menu with master/slave wiring via
Bl-no > SlavNo as described above, changing between the relevant programmer blocks can be done easily via the
-symbol uu. The order is determined by the wiring order (in the above example: 100 Þ 101 Þ 102 Þ 100 Þ ...).
Programmer 9499-040-82711
III-216 APROG ( analog programmer (No. 24)) / APROGD ( APROG data (No. 25))
CONST
0
1
99
APROG
Wp
TNetto
TBrutt
TRest
SegNo
WEnd
ProgNo
SegRes
Bl-no
run
reset
end
fkey
preset
manual
PSet
DBlock
ProgNo
XVal
SlavNo
hide
lock
run
reset
preset
search
p-show
halt
manfree
100 ts=11
Programmer
APROG
Wp
TNetto
TBrutt
TRest
SegNo
WEnd
ProgNo
SegRes
Bl-no
run
reset
end
fkey
preset
manual
PSet
DBlock
ProgNo
XVal
SlavNo
hide
lock
run
reset
preset
search
p-show
halt
manfree
101 ts=11
analog Slave
APROGD
DBlockDBlock
102 ts=11
APROGD
DBlockDBlock
103 ts=11
APROGD
DBlockDBlock
104 ts=11
APROGD
DBlockDBlock
105 ts=11
SELV2
Y1
Casc
X1
X2
X3
X4
Select
106 ts=11
DPROG
TNetto
TBrutt
TRest
SegNo
ProgNo
SegRes
Bl-no
run
reset
end
fkey
do1
do2
do3
do4
do5
do6
preset
manual
PSet
DBlock
ProgNo
SlavNo
hide
lock
run
reset
preset
p-show
halt
manfree
107 ts=11
digital Slave
DPROGD
DBlockDBlock
108 ts=11
APROGD
DBlockDBlock
109 ts=11
APROGD
DBlockDBlock
110 ts=11
DPROGD
DBlockDBlock
113 ts=11
SELV2
Y1
Casc
X1
X2
X3
X4
Select
114 ts=11
DPROGD
DBlockDBlock
115 ts=11
DPROGD
DBlockDBlock
116 ts=11
SELV2
Y1
Casc
X1
X2
X3
X4
Select
117 ts=11
NOT
not d1
d1
118 ts=11
AINP1
Inp1
fail
a/m
inc
dec
Y
lock
hide
61
APRGD2
DBlockDBlock
111 ts=11
APRGD2
DBlockDBlock
112 ts=11
TEXT
Index
Index
Casc
UsrLan
119 ts=11
Fig. 49 Programmer with two analog and one digital blocks