Model No. WETL20708.0 Serial No. Write the serial number in the space above for reference. Serial Number Decal QUESTIONS? As a manufacturer, we are committed to providing complete customer satisfaction. If you have questions, or if there are missing parts, please contact us at the numbers or addresses listed below: Call: 08457 089 009 Outside UK: 0 (44) 113 3877133 Fax: 0 (44) 113 3877125 E-mail: csuk@iconeurope.com Write: ICON Health & Fitness, Ltd.
TABLE OF CONTENTS WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 ASSEMBLY . . . . . . . . . . .
IMPORTANT PRECAUTIONS WARNING: To reduce the risk of serious injury, read all important precautions and instructions in this manual and all warnings on your treadmill before using your treadmill. ICON assumes no responsibility for personal injury or property damage sustained by or through the use of this product. 1. Before beginning this or any exercise program, consult your physician. This is especially important for persons over age 35 or persons with pre-existing health problems. cuit.
20. Do not attempt to raise, lower, or move the treadmill until it is properly assembled. (See ASSEMBLY on page 6, and HOW TO FOLD AND MOVE THE TREADMILL on page 15.) You must be able to safely lift 45 lbs. (20 kg) to raise, lower, or move the treadmill. 24. Never drop or insert any object into any opening on the treadmill. 25. 21. When folding or moving the treadmill, make sure that the storage latch is holding the frame securely in the storage position. 22.
BEFORE YOU BEGIN Thank you for selecting the new WESLO® COMPACT XS treadmill. The COMPACT XS treadmill offers a selection of features designed to make your workouts at home more effective. And when youʼre not exercising, the unique treadmill can be folded up, requiring less than half the floor space of other treadmills. ing this manual, please see the front cover of this manual. To help us assist you, note the product model number and serial number before contacting us.
ASSEMBLY Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred to the top of the walking belt or the shipping carton. This does not affect treadmill performance.
1. Identify the Right Handrail (86), which is marked with a sticker. Have a second person hold the Right Handrail near the tube on the Base (79). See the inset drawing. Tie the wire tie in the Right Handrail securely around the end of the Wire Harness (84). Then, pull the other end of the wire tie until the Wire Harness is routed completely through the Right Handrail. 1 Wire Tie Gently pull on the Wire Harness (84) while sliding the Right Handrail (86) down into the tube on the Base (79).
3. Attach the Console Plate (81) to the Handrail Crossbar (83) with two M8 x 16mm Bolts (1) and two M8 Star Washers (5). Make sure the Console Plate is oriented as shown and that the Wire Harness (84) is not pinched. 3 83 81 Remove the wire tie from the Wire Harness (84). 5 1 5 84 1 Wire Tie 4. Remove the console back and the four M4.2 x 12mm Screws (3) from the Console (80). Save the console back and the Screws for step 6. 4 Hold the Console (80) near the Console Plate (81).
5. Set the Console (80) on the Console Plate (81), and insert the excess wire into the Handrail Crossbar (83). Make sure that no wires are pinched. 5 Attach the Console (80) with four M4.2 x 12mm Screws (3); start all four Screws before tightening any of them. 80 81 83 3 6. Attach the console back to the Console (80) with the four M4.2 x 12mm Screws (3) that you removed in step 4. 6 See step 1. Tighten the two M8 x 16mm Bolts (1) on each side of the treadmill. 80 See step 2.
8. Raise the Frame (see HOW TO FOLD THE TREADMILL FOR STORAGE on page 15). Be careful not to crack the Motor Hood (not shown). 8 Bracket Raise the Gas Spring (76) to a vertical position with the cylinder on the bottom as shown. See the two small inset drawings. Using your fingernail or the end of a screwdriver, press on the end of the Gas Spring Clip (77) to loosen it from the Gas Spring. Next, rotate the Gas Spring Clip and pull it out of the Gas Spring. Be careful to avoid losing the Gas Spring Clip.
OPERATION AND ADJUSTMENT THE PRE-LUBRICATED WALKING BELT Your treadmill features a walking belt coated with high-performance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking belt or the walking platform. Such substances will deteriorate the walking belt and cause excessive wear. HOW TO PLUG IN THE POWER CORD This product must be earthed.
CONSOLE DIAGRAM Thumb Pulse Sensor IMPORTANT: If the treadmill has been exposed to cold temperatures, allow it to warm to room temperature before turning on the power. If you do not do this, you may damage the console displays or other electrical components. Plug in the power cord (see page 11). Next, locate the reset/off circuit breaker on the treadmill frame near the power cord. Make sure that the circuit breaker is in the “reset” position. Next, stand on the foot rails of the treadmill.
HOW TO USE THE CONSOLE The priority display can show the elapsed time, the distance that you have walked or run, the speed of the walking belt, or the approximate number of calories you have burned. Press the Priority Display button repeatedly until the priority display shows the information that you are most interested in viewing. Note: While information is shown in the priority display, the same information will not be shown in the lower left or right corner of the display. 1.
4. Measure your heart rate if desired. HOW TO CHANGE THE INCLINE OF THE TREADMILL To measure your heart rate, stand on the foot rails and place your left thumb on the pulse sensor (see the drawing on page 12). Do not press too hard, or the circulation in your thumb will be restricted and your pulse may not be detected. When your pulse is detected, a heart-shaped indicator in the lower right display will flash each time your heart beats, and your heart rate will be shown.
HOW TO FOLD AND MOVE THE TREADMILL HOW TO FOLD THE TREADMILL FOR STORAGE Remove the key and unplug the power cord. CAUTION: You must be able to safely lift 45 lbs. (20 kg) to raise, lower, or move the treadmill. 1. Hold the metal frame firmly in the location shown by the arrow at the right. CAUTION: To decrease the possibility of injury, do not lift the frame by the plastic foot rails. Make sure to bend your legs and keep your back straight as you raise the frame.
HOW TO LOWER THE TREADMILL FOR USE 1. Hold the upper end of the treadmill with your left hand. Pull the latch knob to the right and hold it. It may be necessary to push the frame forward as you pull the knob to the right. Pivot the frame downward and release the latch knob. Frame Latch Knob 2. Hold the metal frame firmly with both hands and lower it to the floor. CAUTION: Do not grip only the plastic foot rails or drop the frame to the floor. Bend your legs and keep your back straight.
TROUBLESHOOTING Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. PROBLEM: The power does not turn on SOLUTION: a. Make sure that the power cord is plugged into a properly earthed outlet (see page 11). If an extension cord is needed, use only a 3-conductor, 14-gauge (1 mm2) cord that is no longer than 5 ft. (1.5 m).
Locate the Reed Switch (88) and the Magnet (41) on the left side of the Pulley (43). Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8 in. (3 mm). If necessary, loosen the M4.2 x 12mm Screw (30), move the Reed Switch slightly, and then retighten the Screw. Reattach the Motor Hood (not shown) and run the treadmill for a few minutes to check for a correct speed reading. 1/8 in.
EXERCISE GUIDELINES WARNING: Before beginning this or any exercise program, consult your physician. This is especially important for persons over age 35 or persons with pre-existing health problems. The pulse sensor is not a medical device. Various factors may affect the accuracy of heart rate readings. The pulse sensor is intended only as an exercise aid in determining heart rate trends in general. These guidelines will help you to plan your exercise program.
PART LIST—Model No. WETL20708.0 Key No. Qty. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 6 2 8 2 6 1 1 16 2 2 2 6 2 1 1 14 2 6 1 1 2 2 4 1 1 4 4 2 14 17 4 14 6 1 1 10 2 2 1 2 1 1 1 1 1 1 1 1 1 1 Description Key No. Qty. M8 x 16mm Bolt M6 x 10mm Bolt M4.
12 21 33 49 6 7 12 21 11 16 10 8 33 12 50 12 48 29 36 29 36 33 47 11 31 23 8 21 27 8 16 39 51 31 10 8 16 51 13 8 16 16 36 29 29 36 37 38 22 26 29 16 52 8 8 46 36 27 40 29 36 31 8 29 51 16 8 36 27 31 51 23 26 26 8 16 82 36 29 45 37 13 29 26 38 8 36 22 43 41 44 16 8 16 27 29 24 29 42 40 16 8 87 36 29 EXPLODED DRAWING A—Model No. WETL20708.
EXPLODED DRAWING B—Model No. WETL20708.
EXPLODED DRAWING C—Model No. WETL20708.
ORDERING REPLACEMENT PARTS To order replacement parts, see the front cover of this manual.
