User manual

9
EN
OPERATING INSTRUCTIONS
NOTE: Before using the tool, read the instruction
book carefully.
INTENDED USE
The power tool is intended for driving in and loosening
screws.
Inspect the screwdriver before using to ensure all parts
are running smoothly and there are no abnormal sounds
or sparks. Before driving fasteners, check behind walls for
wires, other electrical hazards or plumbing. Clear the work
area of all parts and debris that may cause injury by flying
objects. Securely fix the object to be fastened in a vice or
otherwise clamp to avoid injury. Do not attempt to hold
workpiece by hand.
1. CHARGING INSTRUCTIONS
A) CHARGING THE BATTERY
NOTE:
The battery charger supplied is only for the Li-ion battery
installed in the machine. Do not use another battery
charger. The Li-ion battery is protected against deep
discharging.
When the battery is empty, the machine is switched off
by means of a protective circuit: The tool holder no longer
rotates.
When the battery pack is charged for the first time or after
prolonged storage, the battery pack will accept a 100%
charge after several charge and discharge cycles.
B) HOW TO CHARGE YOUR BATTERY PACK (SEE FIG A)
CHARGING PROCEDURE
1) Plug the charger plug into a suitable power outlet.
2) Connect the DC plug to the battery charging socket. The
charging indicator light will illuminate red during charging.
3) After charging for 3-5 hours, the battery is fully charged
once the charging indicator light turns to green.
4) Unplug the charger; disconnect the charger from the
screwdriver. The screwdriver is ready to be used.
Light Status
Red on
Charging
Green on
Fully Charged
WARNING: When battery charge runs out after
continuous use or exposure to direct sunlight
or heat, allow time for the tool to cool down before re-
charging to achieve the full charge.
WARNING: When charging, the charger and
screwdriver may become warm to the touch;
this is normal and does not indicate a problem.
2. SELECTING A BIT (SEE FIG. B1-B3)
Pull the top slide cover backwards completely.
Manually rotate the bit cartridge anti-clockwise until the
desired bit appeared in the top window.
Push the top slide cover forwards completely. The
magnetic chuck will hold the bit firmly in place.
NOTE: The screwdriver will not operate if the top slide
cover is not fully pushed forwards.
3. REPLACING THE BIT IN THE BIT CARTRIDGE
If the bits in the bit cartridge need to be replaced, you can
follow the steps below (See Fig. C1-C4):
1) Pull the top slide cover backwards completely.
2) Push the bit cartridge out from the left window of the
driver.
3) Replace the bit with the desired bit. Ensure the bits
are properly positioned in the bit cartridge and are not
protruding from the back of the bit cartridge.
4) Push the bit cartridge back into the driver completely.
5) Push the top slide cover forwards completely.
Or you can follow the steps below (See Fig. C5-C7):
1) Push the top slide cover to the forward position .
2) Simply pull the worn or broken bit out from the chuck
and replace it with a new one. It will load into the bit
cartridge automatically when the top slide cover is pulled
backwards.
NOTE:
• Only 25mm bits are compatible with the screwdriver.
• If the top slide cover is not pulled backwards fully, the bit
cartridge will get stuck when taking it from the driver. Pull
the top slide cover all the way back.
• The top slide cover may not fully push forwards if the
bit cartridge is not positioned properly. Make sure the
bit cartridge has clicked into place. If the top slide cover
cannot be pushed forwards, turn the bit cartridge slightly
anti-clockwise and try again.
4. FORWARD/REVERSE ROTATING SWITCH (SEE FIG.
D1,D2,D3)
Depress either forward rotating on/off switch or reverse
rotating on/off switch to start the driver. Fully release
pressure off the forward rotating on/off switch or reverse
rotating on/off switch to stop the driver.
Press the forward rotating on/off switch for driving in
screws. Press the reverse rotating on/off switch for
removing or loosening screws.
NOTE: This screwdriver cannot be used as a drill.