User`s guide

73
CHAPTER 4 - KEYPAD (HMI) OPERATION
NOTE!
It is possible that during programming occurs the error E24
caused by incompatibilitybetween some parameters already
programmed.
In this case do not stop with the parameter setting. If at the
end of the parameter setting does not disappear, check the
table of incompatibilities (table 4.1).
Table 4.1
- Incompatibility of parameters - E24
JOG
P265
=
3 and other(s) DI(s)

Start
-
Stop or FWD and REV or ON and OFF
P266
=
3 and other(s) DI(s)

Start
-
Stop or FWD and REV or ON and OFF
P267
=
3 and other(s) DI(s)

Start
-
Stop or FWD and REV or ON and OFF
P268
=
3 and other(s) DI(s)

Start
-
Stop
or FWD and REV or ON and OFF
Local/Remote
Two or more parameters between P264, P265, P266, P267 and P268 equal to 1
(LOC/REM)
Disables Flying
Start
P265
=
13 and P266
=
13 or
P267
=
13 or
P268
=
13
Reset
P265
=
10 and
P2
66
=
10 or
P267
=
10 or
P268
=
1
0
On/Off
P263
=
14 and
P2
64

14 or
P263

14 and
P2
64
=
14
Direction of
R
otation
Two or more parameters P264, P265, P266, P267 and P268 = 0 (
D
irection of
R
otation)
FWD/REV
P263
=
8 and P264

8 and P264

13
P263
=
13 and P264

8 and P264

13
P263

8 and P263

13 and P264
=
8
P263
=
8 or 13 and P264
=
8 or 13 and P265
=
0 or P266
=
0 or P267
=
0 or P268
=
0
P263
=
8 or 13 and P264
=
8 or 13 and P231

2
Multispeed
P221
=
6 or P222
=
6 and P264

7 and P265

7 and P266

7 and P267

7 and P268

7
P221

6 and P222

6 and P264
=
7 or P265
=
7 or P266
=
7 or P267
=
7 and P268
=
7
Electronic
Potentiometer
P221 = 4 or P222 = 4 and P265

5 or 16 and P266

5 or 16 and P267

5 or 16 and
P268

5 or 16
P221

4 or P222

4 and P265 = 5 or 16 or
P266 = 5 or 16 or P267 = 5 or 16 or
P268 = 5 or 16
P265
=
5 or 16 and P266

5 or 16 and P268

5 or 16
P266
=
5 or 16 and P265

5 or 16 and P267

5 or 16
P267
=
5 or 16 and P266

5 or 16 and P268

5 or 16
P268
=
5 or 16 and P265

5 or 16 and P267

5 or 16
Rated
C
urrent
P295 incompatible with the inverter model
DC Braking and
Ride
-
through
P300

0 and P310 = 2 or 3
PID
P203
=
1 and P221
=
1,4,5,6,7 or 8 or P222
=
1,4,5,6,7 or 8
Ramp 2
P265
=
6 and P266
=
6 or P265
=
6 and P267
=
6 or P265
=
6
and P268
=
6
P266
=
6 and P267
=
6 or P267
=
6 and P268
=
6 or P266
=
6 and P268
=
6
P265
=
6 or P266
=
6 or P267
=
6 or P268
=
6 and P263
=
13
P265
=
6 or P266
=
6 or P267
=
6 or P268
=
6 and P264
=
13
P265
=
6 or P266
=
6 or P267
=
6 or P268
=
6 and P2
63
=
13
P265
=
6 or P266
=
6 or P267
=
6 or P268
=
6 and P264
=
13
Model
P221
=
2,3,7 or 8 and standard inverter
P221
=
2,3,7 or 8 and standard inverter
Analog
Input
P221
=
1 or P222
=
1 and P235
=
2, 3, 4 or 5
P221 or P222
=
2 or 3 and P239
=
2, 3, 4
or 5
Programming Error – E24