2000 PSI ELECTRIC PRESSURE WASHER 4002910 Model # PW19 For replacement parts visit WENPRODUCTS.COM bit.ly/wenvideo IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions.
TABLE OF CONTENTS Technical Data Safety Introduction Pressure Washer Safety Rules Electrical Safety Rules Know Your Pressure Washer Assembly & Adjustments Operation Maintenance & Storage Troubleshooting Exploded View and Parts List Warranty Statement 2 3 4 6 7 8 10 12 13 14 16 TECHNICAL DATA Model Number: Motor: Rated Pressure: Maximum Pressure: Maximum Flow Rate: Rated Water Temperature: Maximum Inlet Pressure: Minimum Inlet Pressure: High Pressure Hose Length: Power Cord Length: Detergent Bottle Capacit
SAFETY INTRODUCTION Thanks for purchasing the WEN Pressure Washer. We know you’re excited to put your machine to work, but first, please take a moment to read through the manual. This manual provides information regarding potential safety concerns, as well as helpful assembly and operating instructions. Safety is a combination of common sense, staying alert, and knowing how your tool works.
PRESSURE WASHER SAFETY RULES WARNING: To avoid mistakes and serious injury, do not plug in your tool until you have read and understood the following safety rules. Learn the tool’s applications, limitations, and possible hazards to maximize your safety and the lifetime of the tool. BEFORE OPERATION 1. KNOW YOUR TOOL. Be thoroughly familiar with the controls of your pressure washer. Know how to stop the water pressure quickly by releasing the trigger, shutting off the unit and turning off the water supply.
PRESSURE WASHER SAFETY RULES OPERATING THE PRESSURE WASHER 1. STAY ALERT. Watch what you are doing and use common sense when operating your tool. Do not use the tool while you are tired or under the influence of drugs, alcohol, or medication. A moment of inattention during operation may result in serious bodily injury. 2. INJECTION HAZARD. The high pressure stream of water can cut through skin and cause serious injury. Keep clear of the nozzle.
ELECTRICAL SAFETY RULES DOUBLE-INSULATED TOOLS Your pressure washer electrical system is double insulated, where two systems of insulation are provided instead of grounding. Double insulated tools do not need to be grounded, nor should a means for grounding be added to the product. IMPORTANT: Servicing a double-insulated product requires extreme care and knowledge of the system, and should be done only by a qualified service personnel using identical replacement parts.
KNOW YOUR PRESSURE WASHER Carefully unpack the tool from the packaging. Check all components and compare against the diagram below. If any part is damaged or missing, please contact our customer service at (800) 232-1195, M-F 8-5 CST or email us at techsupport@wenproducts.com. Carrying Handle High Pressure Hose ON/OFF Switch Water Outlet Water Inlet with Filter (Back) Trigger Adjustable Nozzle Spray Lance Safety Lock Detergent Bottle (13 fl. oz.
ASSEMBLY & ADJUSTMENTS WARNING: To avoid injury from accidental startups, be sure that the tool is switched off and disconnected from the power supply before performing assembly, inspection or adjustments. ASSEMBLING THE HIGH PRESSURE HOSE (Fig. 1 & 2) 2. Connect the opposite end of the high pressure hose 1. Remove the white cap. Connect the coupler end of the high pressure hose to the pressure washer water out- into the connector located on the back of the gun.
ASSEMBLY & ADJUSTMENTS USING THE SPRAY GUN (Fig. 7) 1. The spray gun is equipped with a safety lock on the bottom of the handle. To engage safety, push out the safety lock. To release safety, push in the safety lock. To prevent risk from accidental startups, always engage the safety lock when not using the pressure washer. 2. The trigger starts and stops the water flow. Disengage the safety lock and pull back the trigger to begin operating the pressure washer. Release the trigger to stop the water flow.
OPERATION WARNING: To prevent serious injury, make sure all the warnings and instructions have been read and understood before operating this tool. PREPARING THE PRESSURE WASHER 1. Place the pressure washer on a secure, stable surface to prevent it from tipping during operation. 2. Check that all connections have been properly installed and secured according to the instructions on page 8. • The high pressure hose is properly fastened to the machine water outlet and the gun hose connector.
OPERATION THERMAL PROTECTOR Your pressure washer is also equipped with a motor thermal protector. When the motor is experiencing overload and over heats, the thermal protector will trip to shut down and protect the motor. Wait a few minutes for the motor to cool down and the thermal protector will reset automatically. PRESSURE WASHING TIPS 1. Before pressure washing any surface, test spray an inconspicuous area.
MAINTENANCE & STORAGE WARNING: Risk of electric shock - Always switch off the pressure washer, disconnect the power plug and turn off the water before performing any adjustments or maintenance. NOTE: Replacement parts can be ordered from wenproducts.com by searching the part number (refer to the exploded view and parts list on pages 14 & 15). Use only identical replacement parts designated from your pressure washer. Parts that wear down over the course of normal use (such as hoses, filters, nozzles, etc.
TROUBLESHOOTING WARNING: Stop using the tool immediately if any of the following problems occur or risk serious personal injury. Repairs and replacements should only be performed by authorized personnel. If you have any questions, please contact our customer service at (800) 232-1195, M-F 8-5 CST. PROBLEM Machine doesn’t turn on. CAUSE SOLUTION 1. GFCI plug is tripped 2. Thermal protector is tripped. 3. Machine is not plugged in or the outlet does not have adequate power. 4.
EXPLODED VIEW & PARTS LIST 14
EXPLODED VIEW & PARTS LIST No. Part No. Description Qty. 1 PW19-001 Screw ST3.5x32 8 2 PW19-002 Housing (Left & Right) 2 3 PW19-003 Motor Cover A (Right) 1 4 PW19-004 Support Ring 6 5 PW19-005 Motor Cover B (Right) 1 6 PW19-006 Motor Case 1 7 PW19-007 Motor 1 8 PW19-008 Pump 1 9 PW19-009 Housing (Back) 1 10 PW19-010 Screw ST3.
LIMITED TWO YEAR WARRANTY WEN Products is committed to build tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of two (2) years from date of purchase.
