Use and Care Manual

INSTALLING THE PARALLEL FENCE (Fig. O)
ASSEMBLY & ADJUSTMENTS
13
ASSEMBLY
• Replace the outer flange and nut and
tighten securely with the two spanners
provided (fig. 8). Check that both
blade flanges are in contact with the
blade.
• Unscrew the screw & washer from
the metal bracket (fig. 9).
• Put the metal bracket under the
plastic housing then slide it into the
slot (fig. 10-11).
• The metal bracket can be fixed into
position using the screw supplied
(fig. 12). Ensure the metal bracket is
in line with the diamond disc.
• Insert the blade guard into the notch
then tighten the screw (fig. 3).
• Put the cover (45º vertical fence)
back into position.
INSTALLATION OF THE
PROTECTIVE GUARD (Fig. 13-14)
• Unplug the tile saw from the mains
supply.
• Place the guard onto the metal
bracket (fig. 13) and fix in place using
the screw and washer. Push the
red cover cap over the nut (fig. 14).
• Cover the diamond disc with
the guard.
• Ensure that protective guard can
move freely and that it cannot touch
the disc.
• Do not over tighten the protective
guard when fixing it. The guard
should be free to rise and fall as the workpiece is pushed towards the disc.
INSTALLATION OF THE PARALLEL GUIDE (Fig. 15-16)
• Unplug the tile saw from the mains supply.
• Put the parallel guide onto the working table and fix it using the plastic securing
knobs (fig. 15).
• Mitre cutting can be performed by using the mitre cutting guide. The angle can
be adjusted from 0° to 45° by unscrewing the red palstic screw.
• To perform 45° bevel cut, raise one side of the table, lever out the support and
locate the labs into the corresponding holes in the deck (fig. 16).
Ensure that the deck is correctly secured before working.
fig.10
fig.12
fig.14
fig.16
fig.9
fig.11
fig.13
fig.15
13
ASSEMBLY
• Replace the outer flange and nut and
tighten securely with the two spanners
provided (fig. 8). Check that both
blade flanges are in contact with the
blade.
• Unscrew the screw & washer from
the metal bracket (fig. 9).
• Put the metal bracket under the
plastic housing then slide it into the
slot (fig. 10-11).
• The metal bracket can be fixed into
position using the screw supplied
(fig. 12). Ensure the metal bracket is
in line with the diamond disc.
• Insert the blade guard into the notch
then tighten the screw (fig. 3).
• Put the cover (45º vertical fence)
back into position.
INSTALLATION OF THE
PROTECTIVE GUARD (Fig. 13-14)
• Unplug the tile saw from the mains
supply.
• Place the guard onto the metal
bracket (fig. 13) and fix in place using
the screw and washer. Push the
red cover cap over the nut (fig. 14).
• Cover the diamond disc with
the guard.
• Ensure that protective guard can
move freely and that it cannot touch
the disc.
• Do not over tighten the protective
guard when fixing it. The guard
should be free to rise and fall as the workpiece is pushed towards the disc.
INSTALLATION OF THE PARALLEL GUIDE (Fig. 15-16)
• Unplug the tile saw from the mains supply.
• Put the parallel guide onto the working table and fix it using the plastic securing
knobs (fig. 15).
• Mitre cutting can be performed by using the mitre cutting guide. The angle can
be adjusted from 0° to 45° by unscrewing the red palstic screw.
• To perform 45° bevel cut, raise one side of the table, lever out the support and
locate the labs into the corresponding holes in the deck (fig. 16).
Ensure that the deck is correctly secured before working.
fig.10
fig.12
fig.14
fig.16
fig.9
fig.11
fig.13
fig.15
INSTALLING THE PROTECTIVE GUARD (Fig. M to N)
13
ASSEMBLY
• Replace the outer flange and nut and
tighten securely with the two spanners
provided (fig. 8). Check that both
blade flanges are in contact with the
blade.
• Unscrew the screw & washer from
the metal bracket (fig. 9).
• Put the metal bracket under the
plastic housing then slide it into the
slot (fig. 10-11).
• The metal bracket can be fixed into
position using the screw supplied
(fig. 12). Ensure the metal bracket is
in line with the diamond disc.
• Insert the blade guard into the notch
then tighten the screw (fig. 3).
• Put the cover (45º vertical fence)
back into position.
INSTALLATION OF THE
PROTECTIVE GUARD (Fig. 13-14)
• Unplug the tile saw from the mains
supply.
• Place the guard onto the metal
bracket (fig. 13) and fix in place using
the screw and washer. Push the
red cover cap over the nut (fig. 14).
• Cover the diamond disc with
the guard.
• Ensure that protective guard can
move freely and that it cannot touch
the disc.
• Do not over tighten the protective
guard when fixing it. The guard
should be free to rise and fall as the workpiece is pushed towards the disc.
INSTALLATION OF THE PARALLEL GUIDE (Fig. 15-16)
• Unplug the tile saw from the mains supply.
• Put the parallel guide onto the working table and fix it using the plastic securing
knobs (fig. 15).
• Mitre cutting can be performed by using the mitre cutting guide. The angle can
be adjusted from 0° to 45° by unscrewing the red palstic screw.
• To perform 45° bevel cut, raise one side of the table, lever out the support and
locate the labs into the corresponding holes in the deck (fig. 16).
Ensure that the deck is correctly secured before working.
fig.10
fig.12
fig.14
fig.16
fig.9
fig.11
fig.13
fig.15
2. Secure it in place using the screw and washer. Push
the red cover cap over the nut (Fig. N).
3. Cover the diamond disc with the upper blade guard.
NOTE: Do not over-tighten the protective guard. The
guard should rise and fall freely as the workpiece is
pushed towards the disc during cutting operation. En-
sure the protective guard cannot touch the cutting disc.
1. Take the upper blade guard and position it onto the
metal bracket as shown (Fig. M). Avoid contacting the
blade with your hand.
Fig. M
Fig. N
Fig. O
1. Pull open the two fence lock knobs on the sides of
the parallel fence.
2. Fit the fence onto the rim of the work table. Close
the fence lock knobs to lock the parallel fence in place
(Fig. O).
12