Use and Care Manual

nuts securely.
WARNING: Always make sure your bench grinder
is securely mounted to a workbench. Failure to do so
could result in an accident resulting in possible seri-
ous personal injury.
14
Fig. 10
Fig. 13
Fig. 14
Fig. 11
A - On/Off switch
A
Fig. 12
A - Work rest
A
C
A
B
A - Vise
B - Lawn mower blade
C - Screwdriver
A
A
CHISEL SHARPENING
A - LED light switch
13
E
F
A
C
D
B
Fig. 6
A - Work rest (right)
B - Washer
C - Star washer
D - Work rest bracket
E - Work rest knob
F - Bracket knob
G - Pin
H - Carriage bolt
I - Washer
Fig. 7
A - Battery cover
B - Batteries AAA
A
B
Fig. 8
Fig. 9
A - Bolt
B - Washers
C - Lock washer
D - Hex nut
D
C
B
A
B
A - Coolant tray bracket
B - Coolant tray
A
B
G
H
I
ASSEMBLY
INSTALLING THE COOLANT TRAY (Fig. 4)
Place the coolant tray (L) over the coolant tray bracket then
firmly push tray down onto the bracket to secure it in place.
INSTALLING THE LED BATTERIES (Fig. 5 & 6)
1. The LED light switch is on top of the spark shield assembly.
Make sure that the LED button has been pushed to the OFF
position when installing batteries.
2. Remove the battery covers from the top of the LED assem-
blies.
3. Install the AAA batteries (O) inside the battery compartments
according to the polarity indicators, then replace the battery cov-
ers.
4. Repeat the steps above for the other LED light.
MOUNTING TO THE WORK SURFACE (Fig. 7)
The bench grinder should be firmly attached to a reliable work
surface using mounting hardware (not included) through the
base of the grinder’s mounting holes.. This will prevent the
bench grinder from vibration, walking or tipping during opera-
tion.
NOTE: This bench grinder is compatible with the WEN 4288
Cast Iron Bench Grinder Pedestal Stand.
1. Prepare 1/4 in. bolts, flat washers, lock washers and hex nuts
(not included). The bolt length should be 1-1/2 in. longer than
the thickness of the workbench.
2. Locate and mark the holes where the grinder is to be mount-
ed onto the work surface. NOTE: If mounting to a work bench,
drill four 3/8 in. diameter holes through the workbench.
3. Place the bench grinder onto the workbench, aligning holes in
base with holes in the workbench.
4. Insert four 1/4 in. diameter bolts and washers and attach with
13
E
F
A
C
D
B
Fig. 6
A - Work rest (right)
B - Washer
C - Star washer
D - Work rest bracket
E - Work rest knob
F - Bracket knob
G - Pin
H - Carriage bolt
I - Washer
Fig. 7
A - Battery cover
B - Batteries AAA
A
B
Fig. 8
Fig. 9
A - Bolt
B - Washers
C - Lock washer
D - Hex nut
D
C
B
A
B
A - Coolant tray bracket
B - Coolant tray
A
B
G
H
I
L
Coolant Bracket
LED Switch
Battery Cover
O
13
E
F
A
C
D
B
Fig. 6
A - Work rest (right)
B - Washer
C - Star washer
D - Work rest bracket
E - Work rest knob
F - Bracket knob
G - Pin
H - Carriage bolt
I - Washer
Fig. 7
A - Battery cover
B - Batteries AAA
A
B
Fig. 8
Fig. 9
A - Bolt
B - Washers
C - Lock washer
D - Hex nut
D
C
B
A
B
A - Coolant tray bracket
B - Coolant tray
A
B
G
H
I
11
Bolt
Washer
Washer
Lock
Washer
Hex Nut
Fig. 4
Fig. 5
Fig. 6
Fig. 7