MODEL 4227 17-INCH 12-SPEED DRILL PRESS Instruction Manual NEED HELP? CONTACT US! Have product questions? Need technical support? Please feel free to contact us: 1-800-232-1195 (M-F 8AM-5PM CST) TECHSUPPORT@WENPRODUCTS.COM IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance.
CONTENTS WELCOME 3 Introduction...................................................................................................... 3 Specifications.................................................................................................... 3 SAFETY 4 General Safety Rules......................................................................................... 4 Drill Press Safety Warnings.............................................................................. 6 Electrical Information...
INTRODUCTION Thanks for purchasing the WEN Drill Press. We know you are excited to put your tool to work, but first, please take a moment to read through the manual. Safe operation of this tool requires that you read and understand this operator’s manual and all the labels affixed to the tool. This manual provides information regarding potential safety concerns, as well as helpful assembly and operating instructions for your tool. SAFETY ALERT SYMBOL: Indicates danger, warning, or caution.
GENERAL SAFETY RULES WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Safety is a combination of common sense, staying alert and knowing how your item works. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. SAVE THESE SAFETY INSTRUCTIONS. WORK AREA SAFETY 1. Keep work area clean and well lit.
GENERAL SAFETY RULES WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Safety is a combination of common sense, staying alert and knowing how your item works. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. SAVE THESE SAFETY INSTRUCTIONS. 7.
DRILL PRESS SAFETY WARNINGS WARNING! Do not operate the power tool until you have read and understood the following instructions and the warning labels. DRILL PRESS SAFETY 1. TOOL PURPOSE. This drill press is designed to drill through metal and wood. Drilling through other materials could result in fire, injury, or damage to the workpiece. Using machine for any other purpose other than it’s intended purpose may result in serious injuries, machine damage and voiding of warranty. 2. MACHINE MOUNTING.
DRILL PRESS SAFETY WARNINGS WARNING! Do not operate the power tool until you have read and understood the following instructions and the warning labels. 15. After turning off the drill press, wait until the spindle comes to a complete stop before touching the workpiece. Always turn the drill OFF before removing scrap from the table. 17. CLEANING. Never use solvents to clean plastic parts. Solvents could dissolve or otherwise damage the material. Use only a soft damp cloth to clean plastic parts. 16.
ELECTRICAL INFORMATION GROUNDING INSTRUCTIONS In the event of a malfunction or breakdown, grounding provides the path of least resistance for an electric current and reduces the risk of electric shock. This tool is equipped with an electric cord that has an equipment grounding conductor and a grounding plug. The plug MUST be plugged into a matching outlet that is properly installed and grounded in accordance with ALL local codes and ordinances. 1. Do not modify the plug provided.
UNPACKING & PACKING LIST UNPACKING With the help of a friend or trustworthy foe, such as one of your in-laws, carefully remove the drill press from the packaging and place it on a sturdy, flat surface. Make sure to take out all contents and accessories. Do not discard the packaging until everything is removed. Check the packing list below to make sure you have all of the parts and accessories.
KNOW YOUR DRILL PRESS P A I J C D B H P O K L E M Q N R S G F U T A B C D E F G 10 Belt Tension Adjustment Handle Work Light Laser and Work Light Switches Spring Housing Column Collar Table Locking Handle Bevel Scale H I J K L M N Pulley Cover Chuck Key Power Switch Depth Adjustment Scale Chuck Feed Handles Table O P Q R S T U Motor Motor Locking Wing Screw Column Table Adjustment Crank Rack Base Bevel Lock Bolt
ASSEMBLY & ADJUSTMENTS WARNING: If any part is missing or damaged, do not plug the drill press in until the missing or damaged part is repaired or replaced. ASSEMBLY 1. Position the base on the floor. Attach the column to the base using four M10x30 hex head bolts (Fig. 2). Fig. 2 Fig. 3 1 2 2. Loosen the set screw (Fig. 3 - 1) and remove the column collar (Fig. 3 - 2) and gear rack (Fig. 3 - 3) from the column.
ASSEMBLY & ADJUSTMENTS ASSEMBLY (CONT.) Fig. 9 8. Assemble the hub cover (Fig. 9 - 1) and fasten it in place with a M6x16 flat head screw (Fig. 9 - 2). Attach the three handle caps (Fig. 10 -1). 9. To install the LED light assembly, connect the lamp plug contact (Fig. 11 - 2) to the power source plug contact (Fig. 11 - 3) within the drill’s head. 1 10. Use four pan head screws (Fig. 11 - 1) to install the lamp assembly on the drill press head. Flip the LED lamp switch (Fig.
ASSEMBLY & ADJUSTMENTS REMOVING THE CHUCK (FIG. 14) Fig. 14 1. Turn the feed handles to lower the chuck to the lowest position. 2. Slide the drift key into the opening in the quill. Tap on the drift key using a hammer (not included). The chuck and arbor will drop out. NOTE: To avoid possible damage to the drill or chuck, be prepared to catch the chuck as it falls. As a safeguard, the table can be raised to its maximum height as a backup in case you miss the falling chuck.
ASSEMBLY & ADJUSTMENTS FEED DEPTH ADJUSTMENT Fig. 19 1 Turn the depth scale ring to the desired depth (Fig. 19 - 1). Lock the scale ring in place with the depth knob (Fig. 19 - 2). The spindle will now stop after traveling the selected distance. 2 SPEED ADJUSTMENT (FIG. 20 & 21) This drill press has 12 speeds. The speeds can be changed by changing the belt locations on the motor pulleys as shown in Fig. 21. To change the locations on the pulleys, open the belt cover. Loosen the wing screw (Fig.
ASSEMBLY & ADJUSTMENTS INSTALLING A DRILL BIT Fig. 23 1. Place the chuck key (Fig. 23 - 1) into the side keyhole of the chuck (Fig. 23 - 2), meshing the key with the gear teeth. 2. Turn chuck key counterclockwise to open the chuck jaws. 2 3. Insert a drill bit into the chuck so the chuck jaws grip as much of the bit’s shank as possible. 4. Center the drill bit in the chuck jaws before the final tightening of the chuck. 5.
ASSEMBLY & ADJUSTMENTS USING THE LASER GUIDE WARNING: Do not stare directly at the laser beam. Please observe all safety rules. • Never aim the beam at a person or an object other than the workpiece. • Do not project the laser beam into the eyes of others. • Always make sure the laser beam is aimed at a workpiece that does not possess reflective surfaces, as the laser beam could project into your eyes or the eyes of others. The laser guide should be adjusted prior to operation. To adjust the laser guide: 1.
OPERATION DRILLING SPEEDS There are a few important factors to keep in mind when determining the best drilling speed: material type, hole size, drill bit or cutter type, and desired quality level. Smaller drill bits require greater speed than larger drill bits. Softer materials require greater speed than harder materials. See page 14 for recommended speeds for particular materials. DRILLING METAL • Use metal-piercing twist drill bits.
TROUBLESHOOTING GUIDE PROBLEM Noisy operation SOLUTIONS 1) Adjust the belt tension (See REPLACE THE BELT section) 2) Lubricate the spindle 3) Tighten the retaining nut on the pulley insert 4) Tighten the set screw on the side of the motor pulley The drill bit burns or 1) Drilling at the incorrect speed 1) Change the speed smokes 2) The wood chips are not coming out 2) Retract the drill bit frequently to clear the of the hole chips 3) Sharpen or replace the drill bit 3) Dull drill bit 4) Feeding the workpie
EXPLODED VIEW & PARTS LIST No.
EXPLODED VIEW & PARTS LIST 20
WARRANTY STATEMENT WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship during personal use for a period of two (2) years used for professional or commercial use.
NOTES 22
NOTES 23
THANKS FOR REMEMBERING V. 2020.01.
