MODEL 4210, 4210T 10" DRILL PRESS WITH LASER CROSSHAIR ZJ4113Z For replacement parts visit WENPRODUCTS.COM 4005911 IMPORTANT: Your new tool has been engineered and manufactured to WEN’s highest standards for dependability, ease of operation, and operator safety. When properly cared for, this product will supply you years of rugged, trouble-free performance. Pay close attention to the rules for safe operation, warnings, and cautions.
TABLE OF CONTENTS Specifications............................................................................................. 2 Introduction............................................................................................... 3 General Safety Rules.................................................................................. 4 Specific Safety Rules for the Drill Press..................................................... 5 Electrical Information..................................................
INTRODUCTION Thanks for purchasing the WEN Drill Press. We know you are excited to put your tool to work, but first, please take a moment to read through the manual. Safe operation of this tool requires that you read and understand this operator’s manual and all the labels affixed to the tool. This manual provides information regarding potential safety concerns, as well as helpful assembly and operating instructions for your tool. SAFETY ALERT SYMBOL: Indicates danger, warning, or caution.
GENERAL SAFETY RULES Safety is a combination of common sense, staying alert and knowing how your item works. SAVE THESE SAFETY INSTRUCTIONS. WARNING: Read and understand all warnings, cautions and operating instructions before using this tool. Failure to follow all instructions listed below may result in personal injury and tool damage. WORK AREA SAFETY 1. Keep work area clean and well lit. Cluttered or dark areas invite accidents. 2.
GENERAL SAFETY RULES 4. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents. 5. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. 6. Do not overreach.
SPECIFIC RULES FOR THE DRILL PRESS WARNING: Do not let comfort or familiarity with the product replace strict adherence to product safety rules. Failure to follow the safety instructions may result in serious personal injury. 1. TOOL PURPOSE. This drill press is designed to drill through metal and wood. Drilling through other materials could result in fire, injury, or damage to the workpiece.
SPECIFIC RULES FOR THE DRILL PRESS 12. DRILLING THE WORKPIECE. • Allow spindle to reach full speed before drilling the workpiece. • Never start the machine with the drill bit pressed against the workpiece. • Adjust the table or depth stop to avoid drilling into the table. • Set the drill press to the speed that is appropriate for the material being drilled. 13. Do not touch moving pieces. Keep hands away from the drill bit during operation.
ELECTRICAL INFORMATION GROUNDING INSTRUCTIONS IN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides the path of least resistance for an electric current and reduces the risk of electric shock. This tool is equipped with an electric cord that has an equipment grounding conductor and a grounding plug. The plug MUST be plugged into a matching outlet that is properly installed and grounded in accordance with ALL local codes and ordinances. DO NOT MODIFY THE PLUG PROVIDED.
KNOW YOUR DRILL PRESS TOOL PURPOSE Drill presses are mainly used to drill clean, precise cylindrical holes into workpieces or enlarge existing holes. You may also find other uses for your drill press such as reaming, countersinking, counterboring, tapping, etc. Refer to the diagram below and on Page. 10 to become familiarized with the parts and controls of your Drill Press. C BB H I D B E A CC AA G F J K M L X W V Z N O U P T Y A. B. C. D. E. F. G. H. I. J.
ASSEMBLY & ADJUSTMENTS UNPACKING With the help of a friend or trustworthy foe, carefully remove the drill press from the packaging. Make sure to take out all contents and accessories. Do not discard the packaging until the drill press is completely assembled. The column assembly (column, column support, rack, rack collar, and table support bracket) must be attached to the base. The table and table support handles must be attached to the table support bracket.
ASSEMBLY & ADJUSTMENTS WARNING: Do not plug in or turn on the tool until it is fully assembled according on the instructions. Failure to follow the safety instructions may result in serious personal injury. ATTACHING COLUMN ASSEMBLY TO BASE See Fig. 2 1. Place the column tube on the base, aligning the column support holes to the base holes. 2. Install a hex head bolt in each column support hole and tighten bolts using the adjustable wrench (not included). ATTACHING TABLE TO COLUMN 1.
ASSEMBLY & ADJUSTMENTS DRILL PRESS HEAD TO COLUMN See Fig. 6 CAUTION: The drill press head is heavy. To avoid injury, two people should lift it into position. 1. Carefully lift the drill press head assembly and position it over the column (Fig. 6). 2. Place the mounting opening on the drill press head over the top of the column. Make sure the drill press head is seated properly on the column. 3. Align the direction of the drill press head with the direction of the base and the table. 4.
ASSEMBLY & ADJUSTMENTS 3. Completely remove any burrs found on the inner mating surface of the chuck with a diamond coated tool or a fine file. Use a grade 000 steel wool pad to lightly go over the chuck and spindle. This removes oxidation and dirt that you cannot see. NOTE: Do steps 1-3 even if your chuck is new. New chucks can still have burrs, oxidation, and dirt. 4. Use lacquer thinner or acetone on a lint free rag to clean the chuck. Do not touch these surfaces with your hands after cleaning.
ASSEMBLY & ADJUSTMENTS INSTALL LASER BATTERIES (PRE-INSTALLED) 1. Turn off the drill laser. 2. Pull the tab located below the laser switch and lift up the laser switch cover (Fig. 10). 3. Install two AAA batteries into the battery slots and close the switch cover (Fig. 11). RAISE OR LOWER THE TABLE 1. Loosen the table locking handle and turn the crank handle until the table is at the desired height (Fig. 12). Fig. 10 2. Tighten the table locking handle before drilling. ROTATE THE TABLE 1.
ASSEMBLY & ADJUSTMENTS TILT THE TABLE 1. Loosen the bevel lock bolt (Fig. 14 - 1) with a 19 mm socket or wrench (not included). 2. Tilt the table to the desired angle, using the bevel scale (Fig. 15) as a basic guide. 3. Re-tighten the bevel lock bolt. 1 4. To return the table to its original horizontal position, loosen the bevel lock bolt. 5. Realign the table to the 0° setting on the bevel scale. 6. Tighten the bevel lock bolt with the wrench. Fig.
ASSEMBLY & ADJUSTMENTS FEED DEPTH ADJUSTMENT 1. Loosen the depth locking knob (Fig. 17 - 1). 1 2. Turn the depth scale ring (Fig. 17 - 2) to the desired depth. 2 3. Lock the scale ring in place by tightening the depth locking knob. SPEED ADJUSTMENT For a video demonstration using the WEN 8-Inch Drill Press, visit http://bit.ly/1LGcLIb 1. Unplug the drill press. 2. To change to another one of the five available speeds, open the belt housing cover and loosen the belt tension locking knob (cirled in Fig.
ASSEMBLY & ADJUSTMENTS 1. Unplug the drill press. 2. Place a workpiece on the table. 3. Turn the laser switch to the ON position. 4. Lower the drill bit to meet the workpiece. The two laser lines should cross where the drill meets the workpiece. 2 1 Fig. 19 5. If the laser needs to be adjusted: a. Using a 3 mm hex key, turn the laser adjustment set screws (FIg. 19 - 1) counterclockwise. b. Rotate the laser light housing (Fig.
ASSEMBLY & ADJUSTMENTS REPLACE THE BELT WARNING: Disconnect the drill press from the power source before replacing the belt. 1. Open the housing cover. Loosen the belt tension locking knob (Fig. 21). 2. Remove the belt from the housing cover if it is broken. If it is not broken, but is too stretched to operate correctly, work the belt off the drive (motor) pulley. Then remove the belt from the front spindle. Fig. 21 3. Replace with a new belt.
OPERATION ON/OFF SWITCH WITH SAFETY KEY 1. To turn the drill press ON, insert the yellow safety key (Fig. 22 - 1) into the switch housing (Fig. 22 - 2). As a safety feature, the switch cannot be turned ON without the safety key. 2. Flip the switch upward to the ON position. 3. To turn the drill press OFF, flip the switch downward. 1 ON 2 OFF 4. To lock the switch in the OFF position, remove the safety key (Fig. 22 - 1) from the switch. Store the safety key in a safe place. Fig.
OPERATION GENERAL DRILLING GUIDELINES - DRILLING A HOLE WARNING: To prevent the workpiece and the backup material from slipping from your hand while drilling, position the workpiece and backup material to the left side of the column. If the workpiece and the backup material are not long enough to reach the column, clamp the workpiece and backup material to the table. Failure to do this could result in personal injury. 1.
MAINTENANCE WARNING: To avoid accidents, turn OFF and unplug the tool from the electrical outlet before cleaning, adjusting, or performing any maintenance or lubrication work. WARNING: Any attempt to repair or replace electrical parts on this tool may be hazardous. Servicing of the tool must be performed by a qualified technician. When servicing, use only identical WEN replacement parts. Use of other parts may be hazardous or induce product failure.
TROUBLESHOOTING GUIDE WARNING: Stop using the tool immediately if any of the following problems occur. Repairs and replacements should only be performed by an authorized technician. For any questions, please contact our customer service at (800) 232-1195, M-F 8-5 CST or email us at techsupport@wenproducts.com.
TROUBLESHOOTING GUIDE WARNING: Stop using the tool immediately if any of the following problems occur. Repairs and replacements should only be performed by an authorized technician. For any questions, please contact our customer service at (800) 232-1195, M-F 8-5 CST or email us at techsupport@wenproducts.com.
EXPLODED VIEW & PARTS LIST 107 24
EXPLODED VIEW & PARTS LIST No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Part No.
EXPLODED VIEW & PARTS LIST 26 No. 73 Part No. 4210B-073 Description Flat Washer Qty. 4 No. Part No. Description Qty.
WARRANTY STATEMENT WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of two (2) years from date of purchase.
THANKS FOR REMEMBERING
