Use and Care Manual

A A
B B
C C
D D
E E
F F
G G
H H
J J
K K
L L
M M
N N
P P
R R
T T
24
24
23
23
22
22
21
21
20
20
19
19
18
18
17
17
16
16
15
15
14
14
13
13
12
12
11
11
10
10
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
DRAWN
CHK'D
APPV'D
MFG
Q.A
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
FINISH:
DEBURR AND
BREAK SHARP
EDGES
NAME
SIGNATURE
DATE
MATERIAL:
DO NOT SCALE DRAWING
REVISION
TITLE:
DWG NO.
SCALE:1:5
SHEET 1 OF 1
A0
WEIGHT:
Assembly1
13
This saw uses pinned and pinless blades. Pinned blades are
thicker for stability and for faster assembly. They provide
faster cutting on a variety of materials.
Note: When installing pinned blades, the slot on the blade
holder must be slightly wider than the thickness of the blade.
After the blade is installed, the blade tension mechanism will
keep it in place.
1. To remove the blade, loosen the tension on it by lifting up
the blade tension lever. Turn the lever counterclockwise to
loosen the blade holder if necessary.
2. Remove the table insert. Carefully pry up on the table insert
to remove.
3. Push down on the upper blade holder to remove the blade
from the holder (2). Remove the blade from the lower blade
holder (3).
CAUTION: Install the blade with the teeth pointing down-
ward.
4. To install the blade, hook the blade in the recess of the
lower blade holder (3).
5. While pushing down on the upper blade holder, insert the
blade into the slot of the holder.
7. Move the blade tension lever down and make sure the
blade pin is properly positioned in the blade holders.
8. Adjust the blade to the desired tension. Turning the blade
tension knob clockwise tightens the blade and turning the
knob counterclockwise loosens the blade.
8. Place the table insert back into place.
ASSEMBLY AND ADJUSTMENTS
A A
B B
C C
D D
E E
F F
G G
H H
J J
K K
L L
M M
N N
P P
R R
T T
24
24
23
23
22
22
21
21
20
20
19
19
18
18
17
17
16
16
15
15
14
14
13
13
12
12
11
11
10
10
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
DRAWN
CHK'D
APPV'D
MFG
Q.A
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
FINISH:
DEBURR AND
BREAK SHARP
EDGES
NAME
SIGNATURE
DATE
MATERIAL:
DO NOT SCALE DRAWING
REVISION
TITLE:
DWG NO.
SCALE:1:5 SHEET 1 OF 1
A0
WEIGHT:
Assembly1
Fig. 13
Fig. 15
3
1
BLADE REMOVAL AND INSTALLATION (Fig. 13 to 15)
WARNING: To prevent personal injury, always turn saw OFF and disconnect the plug from
the power source before changing blades or making adjustments.
A A
B B
C C
D D
E E
F F
G G
H H
J J
K K
L L
M M
N N
P P
R R
T T
24
24
23
23
22
22
21
21
20
20
19
19
18
18
17
17
16
16
15
15
14
14
13
13
12
12
11
11
10
10
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
1
1
DRAWN
CHK'D
APPV'D
MFG
Q.A
UNLESS OTHERWISE SPECIFIED:
DIMENSIONS ARE IN MILLIMETERS
SURFACE FINISH:
TOLERANCES:
LINEAR:
ANGULAR:
FINISH:
DEBURR AND
BREAK SHARP
EDGES
NAME
SIGNATURE
DATE
MATERIAL:
DO NOT SCALE DRAWING
REVISION
TITLE:
DWG NO.
SCALE:1:5 SHEET 1 OF 1
A0
WEIGHT:
View7
Fig. 14
2