Description The WEN® Dust Extractor is a powerful yet compact dust collection system. The dust extractor is portable with a 4" diameter collection hose and an adapter set that allows connection to several other dust exhaust port sizes. Includes a filter cartridge and five filter bags with an efficiency rating of 0.5 microns. The WEN® Dust Extractor additionally includes mounting hardware so that the unit may be conveniently stored on a wall, increasing floor space in the workshop.
General Safety Information Warning: For your own safety, read all of the instructions and precautions before operating tool. Caution: Always follow proper operating procedures as defined in this manual — even if you are familiar with use of this or similar tools. Remember that being careless for even a fraction of a second can result in severe personal injury.
Tool Should Be Maintained 1. Always unplug tool prior to inspection. 2. Consult manual for specific maintenance and adjustment procedures. 3. Keep tool lubricated and clean for safest operation. 4. Remove adjusting tools. Form habits of checking to see that adjusting tools are removed before switching the machine on. 5. Keep all parts in working order. Check to determine that the guard or other parts will operate properly and perform their intended function. 6. Check for damaged parts.
CHECK with a licensed electrician or service personnel if you do not completely understand the grounding instructions or whether the tool is properly grounded. USE ONLY THREE-WIRE EXTENSION CORDS that have three-pronged plugs and outlets that accept the tool's plug as shown in Fig. A. Repair or replace a damaged or worn cord immediately. CAUTION: In all cases, make certain the outlet in question is properly grounded. If you are not sure, have a licensed electrician check the outlet.
Assembly Refer to Exploded View, Page 9. Install Casters 1. Thread M10 hex nut and flat washer (Item 29 and 33) onto the threaded stud of one of the casters (Item 31 and 32). 2. Insert threaded stud of caster into hole on the outside bottom of the tank (Item 28) and secure in position with M10 flat washer, lock washer and hex nut (Item 29, 30 and 33) inside tank. 3. Repeat the above steps for the remaining three casters. Mount Filter Cartridge with Filter Bag 1.
Operation Refer to Exploded View, page 9. 1. Position dust extractor on a flat level surface near the dust-producing machine. 2. Connect inlet hose (Item 20) to dust producing machine using hose coupling (Item 21). Use adaptors (Item 27) if needed. 3. Turn dust collector on before starting dust-producing machine. Emptying Extractor Tank Turn switch off and remove plug from power source outlet before emptying collector bag. Refer to Exploded View, page 9. 1.
Troubleshooting Chart Symptom Motor will not run. Excessive dust in air. Possible Cause(s) Defective plug, cord, switch or motor Blown fuse or circuit breaker Leaking bag or hose connection Motor is excessively noisy, Worn brushes growls or pitch has changed. Defective motor Motor fails to develop full power or motor stalls.
Exploded View 9
Parts List Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Stock # 3400-001 3400-002 3400-003 3400-004 3400-005 3400-006 3400-007 3400-008 3400-009 3400-010 3400-011 3400-012 3400-013 3400-014 3400-015 3400-016 3400-017 3400-018 3400-019 3400-020 Description Right Cover Pan Head Screw Pan Head Screw Nut Left Cover Line Cord Strain Relief Top Foam Seal Motor Side Foam Seal Switch Pan Head Screw Locking Strap Filter cartridge Lock Washer Serrated Washer Flange Top Cover Hose Clamp Hose Item 21 22 2
Limited One Year Warranty WEN Products is committed to build tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN CONSUMER POWER TOOLS PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC ("Seller") warrants to the original purchaser only, that all WEN consumer power tools will be free from defects in material or workmanship for a period of one (1) year from date of purchase.
